Three riveted steel pipes are connected in series, with the flow through the system being 1.2 m3/s. (1) Find the total head loss if the pipe diameters and lengths are D1 = 60 cm, D2 = 40 cm, D3 = 54 cm, L1 = 400 m, L2 = 450 m, L3 = 750 m. Assume that the friction factor f = 0.0125 for all three pipes. (2) If the system total head loss is known to be 60 m, determine the

Q: Question: The pressure pipe elbow with 30 degree orientation in the vertical plane is 60 cm in…

A: Solution

Q: 2. Consider the piping network shown. The pressure heads at points A and B are 80m and 52m,…

A: Pressure head at A, hA=80 m Pressure head at B, hB=52 m Head loss, H=80-52=28 m Hazen William…

Q: Figure Q4 shows there are two sections of pipes in the system, which are 38m long of 5 cm diameter…

A: Given, L1 = 38 m  L2 = 45 m D1 = 5 cm or 0.05 m D2 = 15 cm or 0.15 m \ Q = 0.005 m3/s

Q: The flowrate of water through the bend pipe (90o) is 0.21 m3/s. The pipe diameter at the inlet is…

A:

Q: without rupturing. Determine the maximum length, 1, allowed if the roughn 00015 ft and the flowrate…

A:

Q: The three-tanks system in figure are interconnected as shown. Compute the flowrate in each pipe,…

A: Solution: Given Data: Pipe length:L1=2000 m f1=0.013L2=2300 mf2=0.020L3=2500 mf3=0.023Pipe…

Q: As shown in the figure below, the smaller pipe is cut off a short distance past the reducer so that…

A:

Q: Solve for the water discharges in cach steel pipe as shown in Figure 3. You may assume that the…

A:

Q: A 1.20 m-diameter(internal) horizontal steel penstock conveys water at the rate of 3.6 m³/s. The…

A: r = D/2 = 1.2/2 = 0.6m v = Q/A = 3.6πx0.62= 3.183m/s H (head) = 60m For instantaneous closure T ⩽…

Q: From section 1 at p₁-750 kPa, water flows through a galvanized iron pipe of 50 mm inside diameter…

A: Given, P1 = 750 kPa  D = 50 mm L = 40 m  Q = 0.015 m3/s

Q: 8-62 A horizontal pipe has an abrupt expansion from D₁ = 8 cm to D₂ = 16 cm. The water velocity in…

A: We have to find out the downstream pressure P2 and error if bernoulli's equation is used .

Q: D washer (2) n holes of diameter D. To reduce water consumption, a washer is installed in the shower…

A: Velocity in the pipe without reducer at section 1 and at the outlet (considering it as 2):…

Q: Q1: Find the equivalent pipe for the loop shown below, also find the pressure at point C if the…

A: Given, Q=252 m3/hr=0.07 m3/sec Pressure at Point A=450 Kpa CHW=100 PIPE AB BC AC DIAMETER 200…

Q: 7.30 FLUS For this refinery pipe, DA = 20 cm. Dg = 14 cm, and L= 1 m. If crude oil (S = 0.90) is…

A:

Q: Water flows steadily downward through the pipe shown in the figure below. Viscous effects are…

A:

Q: Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in…

A: ##Calculation of diameter of Pipe 2 using hazen Williams equation

Q: Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as…

A: Given that: Vapour Pressure of water: Pv=2.25kPaAtmospheric Pressure, Patm = 100 kPaγwater =9810…

Q: A fire protection system is supplied from a water tower and standpipe 80ft tall. The longest pipe in…

A: Given that :

Q: Calculate the force required to hold a flat plate in equilibrium perpendicular to the flow of water…

A: Calculate the force required to hold a flat plate in equilibrium?

Q: Ex. For the square loop shown: 1. find the discharge in all the pipes. All pipes are 1 km long and…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: z=0.2 m - Dow n 5) The pipe system is designed to deliver 4.24x104 m/s of water. There are minor…

A: Using Bernauli's equation one can get the solution for the given below: Elbow loss =kv22gInlet loss…

Q: ill be the flowrate? The pipes are galvanized iron with k, = 0.0005 ft. Take v = 1.06 x 5 ft/s and…

A: To find:Flow rate

Q: 1. Water flows through a horizontal, 0.5-m-diameter pipe at a rate of 0.9 m³/s (Figure below). It is…

A:

Q: The system consists of a pipe with a diameter of 0.05m and a length of 4 m, and a hemisphere (radius…

A: Solution;

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A: Total length of pipe= 18ftDiameter of pipe = 0.4 inFriction factor = 0.03Loss coefficient For…

Q: QI: Find the equivalent pipe for the loop shown below, also find the pressure at point C if the…

A:

Q: Situation 1 The 60 cm pipe conducts water from reservoir A to a pressure turbine which discharges…

A:

Q: QUESTION 7 Two new cast-iron pipes (ɛ = 0.26 mm) in series connect two reservoirs. Both pipes are…

A: Given data in question  Roughness Diameter  Length Elevation of A Temperature 10 degree Celsius…

Q: Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the…

A: Given:Difference in  elevation=80mf=0.024k1=0.5k2=1.0k3=1.0d=80cmL=2000m

Q: Calculate the minimum value of hz that is necessary to guarantee an outgoing water flow rate of Q m…

A:

Q: 3. Obtain the gage pressure at the center A of the pipe shown. Ignore surface tension effects.…

A:

Q: Q2: A is 4500 m length-gas flow line, and B is 2000 m length-liquid flow line (0.1 m diameter) both…

A: Given:-L=2000mleft side length=2500mmPressure at A - pipe line inlet=2400kPaPressure at C pipe line…

Q: Determine the discharge through the three new cast iron pipes connected in series having diameters…

A:

Q: Q2/ Three pipes are connected in series. The physical properties of the pipes are in Table below. If…

A: PA - PB = 150 kPa ZA - ZB = 5 m  v = 1.02 x 10-6 m2/s

Q: Question: Water is flowing in the vertical pipe system shown in the figure. Water exits to the…

A: The given figure is shown below:

Q: 1. The horizontally lying device or fitting shown below connects three pipelines. Water (γwater =…

A:

Q: Current Attempt in Progress A 1-m-diameter cylindrical mass, M, is connected to a 2-m wide…

A: To find out the required value of M.  Where,  B = 2m H = 2.2 m D = 1m

Q: A vertical pipe system shown in the Figure below, d = 300 mm throughout, carries 0.82 (m³/s) of…

A: ###Calculation of pressure drop between A and B when B is 100 m higher than A in Given pipe system…

Q: The system consists of a pipe with a diameter of 0.05m and a length of 4 m, and a hemisphere (radius…

A: Solution;

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?