Ex. For the square loop shown: 1. find the discharge in all the pipes. All pipes are 1 km long and 300 mm in diameter, with a friction factor of 0.0163. Assume that minor losses can be neglected. 2. If the required pressure at point d=25 m, then find the required pressure in point A 20 4/s 100 4/6 D 40 L/s 40 L/S

Ex. For the square loop shown: 1. find the discharge in all the pipes. All pipes are 1 km long and 300 mm in diameter, with a friction factor of 0.0163. Assume that minor losses can be neglected. 2. If the required pressure at point d=25 m, then find the required pressure in point A 20 4/s 100 4/6 D 40 L/s 40 L/S

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need the answer quickly
Two pipes A and B are connected in parallel between two points. Pipe A is 200 m long and has a diameter of 16 cm, pipe B is 150 m long and has a diameter of 12 cm. Both the pipes have the same friction factor of 0.018. A partially closed valve in pipe 'A' causes the discharge in the two pipes to be the same. All other minor losses can be neglected. The value of the valve coefficient is - Valve F = 0.018 L=200m, d-16cm L,=150m, d=12cm B F = 0.018
Given; A hydraulic jack system (see figure) in an equilibrium condition, and data/properties as shown. Determine the Force F applied at the end of the lever arm to maintain equilibrium of the system. Neglect weight of plungers. Hint: Use the law of transmission pf pressure
A commercial steel pipe—with a diameter, D, of 200 mm and length, L, of 30 m—is used to drain oil (S.G.=0.8)tank. Determine the discharge, in liters per second, when the oil level in the tank is 3 m above the exit of the pipe.Neglect component or minor losses and quantify the friction losses using the Darcy-Weisbach equation shownbelow, use friction factor, f, of 0.12.
For the open tank, the piezometers attached on the side, containing two different immiscible liquids, as shown in the figure, find the elevation of the liquid surface in piezometer A.
A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is four times the velocity head in the 50mm pipe and loss of head from 2 to B is 15 times the velocity head in the 100mm pipe. The pump discharge rate us 50 liters per second. Determine the following: A. Power delivered by the pump in KW B. Pressure head at pt. 1 in meter C. Pressure head at pt 2 in meter
• A simple U tube manometer is given below. The pressure at which side is higher? o Left o Right o Left = right • In order to calculate the pressure difference at locations 1 and 2 (P2 - P1), we need to know the length of the inclined tube L, as is shown below. o True o False A fow section fow device Fluid
The pump whose characteristics are: H, = 80 – 600V²2 %3D n = -1500V² + 700V Elevation = 230 m |(2) (1) Elevation = 200 m 1000 m pipe 40 cm in diameter Pump Figure Q3 is used to pump water (µ=0.001kg/ms) a distance of 1000 m between two reservoirs the elevations of which are shown in Figure Q3 and remain constant. The pipe is 40 cm diameter commercial steel (ɛ=0.046 mm). Ignoring minor losses and assuming fully turbulent flow. Determine d) The volumetric flow rate e) The efficiency at the operating point
Suppose the impeller in the preceding question supplies 10 kW of water power and is placed in a tank 4 m square and 4 m deep. Determine the velocity gradient G (s ¹). The water viscosity is 1.31 x 10-3 Pa-s.
PLEASE PROVIDE A COMPLETE SOLUTION WITH FIGURE FOR ME TO FOLLOW :) ANSWER IS GIVEN FOR REFERENCE. THANK YOU!