The post AB consists of a solid steel pipe of 3.5-in. diameter. A 15-lb block C moving horizontally at velocity v0 hits the post squarely at A. Using E = 29 × 10^6 psi, determine the largest speed v0 for which the maximum normal stress in the pipe does not exceed 23 ksi.

Q: 200 mm 150 mm 100 mm 200 mm

A:

Q: . Motor A develops a power of 2.5 HP and has an attached pulley that rotates at 90 rev/min.…

A: Introduction Using a general torsional equation, we will determine the diameter of the shaft in this…

Q: A rigid plate of negligible mass rests on the middle spring which is higher than the two outer…

A:

Q: Determine the greatest constant angular velocity v of the flywheel so that the average normal stress…

A: Drawing the free body diagram of the wheel,

Q: The solid steel shaft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: Given ,         diameter of shaft=d=25mm=25x10-3m        Revolutions of the shaft n=50 rev/sec…

Q: 5. The A-36 steel tubular shaft is 2 m long and has an outer diameter of 50 mm. When it is rotating…

A: According to0 the given data The length of the tubular shaft is L=2 m. The outer diameter of the…

Q: the solid steel sheft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: Please find the solution below.

Q: 5. The drive shaft AB of an automobile is to be designed as a thin-walled tube. The engine delivers…

A:

Q: solid 22-mm-diameter bronze shaft transmits 13.4 kW at 17 Hz to the propeller of a small sailboat.…

A:

Q: 2 A thin rim 1.8 m diameter and 160 mm wide, is made of steel plate 13 mm thick. The rim is made in…

A:

Q: The 6-hp reducer motor can turn at 1200 rev>min. If the shaft has a diameter of 5 8 in.,…

A: Given: The power of the reducer motor is P=6 hp. The angular velocity of the reducer motor is ω=1200…

Q: A door is constructed of a thin homogeneous slab of material; it has a width of 1 m. If the door is…

A:

Q: The A-36 solid steel shaft is 2 m long and has a diameter of 60 mm. It is required to transmit 60 kW…

A: Given data: The diameter of shaft, d = 60 mm. The length of shaft, L = 2 m. The power transmits, P…

Q: 3. As shown, a 50-kg rigid block is suspended by the three springs whose lower en level. Each steel…

A:

Q: The load D has a mass of 220 kg and is being hoisted by the motor M with constant velocity.…

A:

Q: The connection between an electric motor and a construction machine shaft is provided by means of a…

A: The number of bolts, n = 3The pitch circle diameter of bolt, d = 40 mmThe surface pressure endurance…

Q: Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a…

A: Here, Shaft diameter = dsh = 50 mm Allowable shear stress in shaft = τsh = 100 N/mm2 Pitch circle…

Q: The channel section carries a uniformly distributed load totaling 6W and two concentrated loads of…

A:

Q: The solid steel shaft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: Find the absolute maximum shear stress

Q: A steel gear, with 80-mm diameter rod connected to it is used to transmit 600 HP at 200 rpm. If the…

A: Given: d = 80 mm H = 600 hp n = 200 rpm

Q: A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having…

A: Load developed(P) in the cable is given by:→P=∆L×AELwhere∆L=extension/deformation in cableL=Length…

Q: Problem #2: The solid shaft has a diameter of 40 mm. determine the absolute shear stress in the…

A: Given:- d=40 mm To find:- Absolute maximum shear stress Shear stress distribution diagram

Q: A 90 kN 1.8 m | B 54 kN 2.4 m C 3 m 22 kN/m D 2.4 m E

A:

Q: A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having…

A: Given Data Dia of the cable, 0.4in Weight of the elevator, 800 lb Young modlus of elasticity, E =…

Q: The connecting rod of a four stroke cycle Diesel engine is of circular section and of length 550 mm.…

A:

Q: Determine the magnitude of the shear force at section b-b that lies 0.1 m from A, located 0.1 m…

A: Find the shear force at section b-b.

Q: The rows of staples AB contained in the stapler is glued together so that the maximum shear stress…

A:

Q: RI0-9. The 0-mm-diameter shaft rotates at 300 rev/min. This motion is caused by the unequal belt…

A: Write the magnitudes of unequal tensions,   T1=800 NT2=450 N   Write the expression of net torque on…

Q: For the shown clevis where the bolt has a shearing strength of 207 MPa, determine which of the two…

A:

Q: A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having…

A: Given Data The diameter of the steel cable is: d=0.4 in Weight of the elevator is: W=80 lb The…

Q: The joint proposed provides the connection (pivot) between the clevis 1 and the tie rod 2 by means…

A:

Q: While an oil well is being drilled at a depth of 2100 m, it is observed that the top of the…

A: Given data,  L= 2100 m =2100000 mm d= 200 mm =200 mm  G= 77.2 GPa=77200 N/mm²  Revolution N= 2.5

Q: Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12…

A:

Q: While an oil well is being drilled at a depth of 2000 m, it is observed that the top of the…

A:

Q: Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.