Answered: A steel gear, with 80-mm diameter rod…

A steel gear, with 80-mm diameter rod connected to it is used to transmit 600 HP at 200 rpm. If the rod has a G = 83 GPa and length equal to 6 meters, determine the shear stress of the rod

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a way that the shear stress in shaft does not exceed 100 N/mm2. If six bolt are used to join the flange and the bolt circle is 150 mm in diameter. Determine the diameter of the bolt if the permitted shear stress in the bolt is 80N/mm2.
A steel core is bonded firmly to the copper tube (shell) to form the shaft shown. The length of the shaft is 450 mm and the end A is fixed to the wall. Take the shear modulus of steel and copper as 76 GPa and 38 GPa, respectively. The diameter of the core is 60 mm and the outer diameter of the shaft is 100 mm. Determine the maximum external torque (Tmax) so that the absolute maximum shear stress for any point H on the surface of the copper shell does not exceed 50 MPa. 450 mm A 100 mm 60 mm В Tmax =? kN · m
The cylinder of a hydraulic ram supported at the open end is 200 mm internal diameter and is required to sustain an internal pressure of 25 MN/m2.Calculate the necessary thickness of the wall if the maximum shearing stress is limited to 55 MN/m2.Allowing for the effect of the longitudinal stress caused by the pressure on the end of the cylinder, calculate the increase in diameter due to the application of the 25 MN/m2 pressure. Take E= 214 GN/m2 and υ = 0. 28
While an oil well is being drilled at a depth of 2100 m, it is observed that the top of the 200-mm-diameter steel drill pipe (G= 77.2 GPa) rotates through 2.5 revolutions before the drilling bit starts to operate. Determine the maximum shearing stress caused in the pipe by torsion. The maximum shearing stress caused in the pipe by torsion is MPа.
A solid shaft (100 mm diameter) transmits 75 kW at 150 rpm. Determine the value of maximum shear stress set up in the shaft and the angle of twist per metre of the shaft length if G=80 GN/m².
two solid steel shafts of different diameters are joined together at point C. the diameter of the smaller shaft is 0.5 in, while the diameter of the larger shaft is 1 in. if the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi.Show full solution please
Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 30 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 7 deg. Use G=83 GPa for steel 300 mm 600 mm
Two solid steel shafts of different diameters are joined together at point C. The diameter of the smaller shaft is 0.5 inch, while the diameter of the larger shaft is 1 inch. If the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb is applied at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi. 8 in 5 in 12 in
The driveshaft of an automobile is being designed to transmit 242 hp at 2980 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 6700 psi. Answer: d = in.
The driveshaft of an automobile is being designed to transmit 131 hp at 2960 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 5300 psi. Answer:d = i in.
The driveshaft of an automobile is being designed to transmit 203 hp at 2940 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 7800 psi.
A flanged bolt coupling consists of nine ½ -in diameter bolts equally spaced around a bolt circle 15 inches in diameter. Determine the torque capacity of the coupling if the shear stress in the bolt is limited to 5000 psi. Answer: T = 11.04 kip-ft