A solid circular shaft of length of 3 m and diameter of 50 mm rotates at 1200 rpm by a 400 HP electric motor at its middle. It derives two machines of 150 HP and 250 HP at left and right ends of the shaft, respectively. Determine the maximum shear stress and relative displacement of the two ends of the shaft. Take G = 85 GPa. %3D

A solid circular shaft of length of 3 m and diameter of 50 mm rotates at 1200 rpm by a 400 HP electric motor at its middle. It derives two machines of 150 HP and 250 HP at left and right ends of the shaft, respectively. Determine the maximum shear stress and relative displacement of the two ends of the shaft. Take G = 85 GPa. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800 rev/min. If the maximum allowable shear stress is 60 MN/m? Q4 and the modulus of rigidity, G = 79 GPa, determine the following: c) The relative angle of twist of the ends of the shaft
Mechanics of deformable bodies
Problem: 1 A line shaft rotating at 55 RPS is to transmit 28 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 85 MPa. Determine the diameter of the shaft, neglecting the bending moment on the shaft.
A hollow shaft (do = 2d; where do and d; are the outer and inner diameters respectively) needs to transmit 20 kW power at 3000 RPM. If the maximum permissible shear stress is 30 MPa, do is
A motor driving a solid circular steel shaft transmits 40kW of power at 500 rpm. If the diameter of the shaft is 40 mm, the maximum shear stress in the shaft is MPа.
A solid 1.500-in.-diameter steel shaft is subjected to torques TB = 290 lb-ft and TD= 125 lb-ft, acting in the directions shown. If the allowable shear stress in the shaft is 16 ksi, determine the maximum torque Tc that can be applied to the shaft. TB BILL (2) (1) Answer: Tc= i с Tc (3) TD lb-ft D x
The steel shaft show rotates
3. A solid circular shaft is 1.8 m and is made of steel with G = 70 GPa. When rotating at w = 70 rad/s, it transmits 28 kW of power from engine A to generator B. As the design engineer, you are asked to: (a) Determine the shaft's smallest allowable radius if the allowable shear stress is T allow = 80 MPa. (b) Determine the shaft's smallest allowable radius If the allowable angle of twist is allow = 0.1 rad (in other words, the shaft is restricted not to twist more than 0.1 rad). (c) If both conditions (a) and (b) are required simultaneously, which radius will you select as the allowable radius. (In other words which condition controls the situation)? Briefly explain your answer. (1 kW = 1000 Watts) B
A 3-meter solid steel shaft, with an unknown diameter, twists by 5° as it experienced a shear stress of 60 MPa. What is the diameter of the solid steel shaft? Use G = 83 GPa.
A drilling riser is used to drill a 4km deep hole into the seabed. The riser can be approximated as a hollow steel shaft of 185mm and 160mm outer and inner diameter respectively. If the power exerted is 230kW and the speed of rotation of the drill is 75RPM, calculate the maximum shear stress in the shaft and the twist of one end relative to the other in degrees.(Note the angle of twist of a 4km drill string is going to be >> 360o ) G = 89 kN/mm2