Q3: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to transmit 60 kW at 200 rev/min. The maximum shear stress in the shaft is limited to 70 MN/m2 and the angle of twist to 3.8" in a length of 4 m. For the shaft material G= 80 GN/m2.

Q3: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to transmit 60 kW at 200 rev/min. The maximum shear stress in the shaft is limited to 70 MN/m2 and the angle of twist to 3.8" in a length of 4 m. For the shaft material G= 80 GN/m2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Related questions

Q: A submarine robot explorer is used to explore the marine life in deep water. The weakest point in…

A: The maximum pressure hold by the weakest point on the submarine is given as, P=300 MPa=300×106 Pa

Q: 3. The U.S. auto industry produces approximately 6 million vehicles a year, each containing roughly…

A: Given:The specific weight of each unit is .The wind capacity factor is .The average electric power…

Q: Describe another fundamental principle that relates to the central limit theorem and describe how it…

A: Central limit theorem: This theorem states that the distribution of the samples from a population…

Q: Problem 2 An Air Force Research Lab engineer is asked to evaluate the maximum theoretical work that…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is…

A: Given Solution is Incorrect . Because formula used are not completely correct.

Q: Your family just bought a very small cabin in Estes Park, CO, and they have asked you to help figure…

A: GIVEN: Temp to be achieved = 23° C The internal gains = 600 W The Heat transfer of the whole…

Q: hy do parachutists 'hit and roll'?

A: When they land on ground there speed is quite high so momentum will also be high so they roll to…

Q: The thermal power from the reactor is 2400 MW and this is used to drive (operate) a heat engine. The…

A: Given data Thermal power (input to heat engine) = 2400 MW Efficiency of generator = 75 %…

Question

I need the answer as soon as possible

Q3: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to
transmit 60 kW at 200 rev/min. The maximum shear stress in the shaft is limited to
70 MN/m2 and the angle of twist to 3.8 in a length of 4 m. For the shaft material
G = 80 GN/m2.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
Micro Bh Micros Bb Micros - с * Question Completion Status: Question 2 2.0 d=1.50 in. dia. 1.9 1.8 Class r = 0.08 in. The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when it rotates at 100 rad/s and transmits 5000 lb-in/s. Use CamScanner app or Notes app of iPhone to scan all hand-written pages into one PDF file. Attach the PDF file here to answer in this question. Class ( bbhosted.cuny.edu/webapps/assessment/take/take.jsp?course_assessment_id=_2374 Class D = 2.00 in. dia. r= Fillet radius Class G Cuent Projec suntur Et WA AS hp
The figure shows an inboard engine, 8-ft long steel drive shaft, and propeller for a motor boat. The shaft is to be designed to safely transmit 200 hp at 3500 rev/ min. Determine the diameter of the smallest shaft that can be used and its corresponding angle of twist. For the steel, use a working shear stress of 12 000 psi and G = 12 x 106 psifind, a) diameter b) angle of twist
The dimensions of a stepped shaft are shown below. The maximum shear stress specification of the material is 67.1 MPa. Calculate the allowable torque for the shaft. r= 2.4 mm 12 mm 15 mm
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad
Compute the torsional shear stress in a hollow shaft with an outside diameter of 40 mm and an inside diameter of 30 mm when transmitting 28 kilowatts(kW) of power at a speed of 45 rad/s.
A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
Q/A shaft supported at the ends in ball bearings carries a straight tooth spur gear at its mid span and is to transmit 7.5 kW at 300 r.p.m. The pitch circle diameter of the gear is 150 mm. The distances between the centre line of bearings and gear are 100 mm each. If the shaft is made of steel and the allowable shear stress is 45 MPa, determine the diameter of the shaft. Show in a sketch how the gear will be mounted on the shaft; also indicate the ends where the bearings will be mounted? The pressure angle of the gear may be taken as 20°.
A solid shaft in a rolling mill transmits 30kW at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 80 MPa and an angle of twist of more than 10 degrees in a length of 8 meters. G = 83 GPa
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C.a)Determine the maximum shear stress in the shaft in ksi.b)Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible.