The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. a)Determine the maximum shear stress in the shaft in ksi. b)Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible.

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: The allowable shear stress for brass shaft, The allowable shear stress for aluminum shaft, The value…

Q: 4 mm module 20° full-depth The gear shown above is to transmit 1 kW at a speed of 200 rev/min. Find…

A:

Q: 3.33 The figure shows an inboard engine, 8-fN long steel drive shaft, and propeller for a motor…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: The solid shaft (G=70 GPa) has a diameter of 40 mm. Calculate: a. The magnitude and direction of the…

A:

Q: Hollow and solid shafts have the same material, length and the same outer radius as shown. The inner…

A:

Q: This engine is used in a hoist. Motor 2.5 kW with the help of gears with a power of and n = 500 rpm.…

A:

Q: solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum…

A: for solution refer below images.

Q: A motor drives a shaft at 300 rpm and a power output of 100 kW. The shaft is made of A-36 steel and…

A:

Q: 4. A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip-ft. Use a…

A:

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

A:

Q: Problem 5-57: The turbine develops 150 kW of power, which is transmitted to the gears such that C…

A: Given data as per the questionpower developed =150 kwdiameter of shaft =100 mm =0.1 mRotational…

Q: flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and…

A: The diameter of bigger circle is The diameter of smaller circle is The number of bolts on bigger…

Q: A power source at C actuates valves at A and B through a long round steel control rod. A torque of…

A:

Q: 4 kN m 1.5 kN m Aluminum Steel Bronze B 100 mm 75 mm 3m 2 m 1.5 m- C FIG. P3.12 FIG. P3.11 3.12 The…

A: For solution refer below images.

Q: Consider the 1inch steel square tube loaded in torsion.the tube has wall thickness of 0.0196 inch…

A: Given: maximum allowable shear stress = 7.2 kpsi tube wall thickness = 0.0196 inch Do = 1 inch Di =…

Q: Compute the torsional shear stress (MPa) in a 45-in circular steel shaft with a diameter of 42-mm…

A: The length of the circular shaft, (L)=45 in.The diameter of the shaft, (D)=42 mm.The torque on the…

Q: In the figure, shaft AB transmits power to shaft CD through a set of bevel gears contacting at point…

A:

Q: Two motors deliver 119 hp each at 1000 rpm to shafts at A and D. The shaft transmits torque through…

A: Data given-  Motor deliver = 119 hp  N = 1000 rpm  Shear modulus = 11 × 103 ksi

Q: PROBLEM 2. The turbine in the figure generates 90 kW power. 50 kW of power is drawn from the gear at…

A: Total Power P = 90kW  Power with gear C Pc = 50kW = 50×103 W Power with gear D PD = 40kW = 40×103 W…

Q: L1=1.8 L2=.9 d1=70 d2=53 Compound shaft ACB is fixed at A and consisting of two solid circular…

A: Given data:- The length L1 is L1 = 1.8 m. The length L2 is L2 = 0.9 m. The diameter D1 is D1 = 70…

Q: The 2.3-in.-diameter drive shaft AB on the helicopter in (Figure 1) is subjected to an axial tension…

A: Given data:- Diameter of the shaft =2.3-in. Axial tension (P)=10000 lb torque (T) =345 lb⋅ft To…

Q: Missing value MT = M0 (kN.m) 170 Kindly write legibly. Thank you Solve for: a) Determine the shear…

A:

Q: Please give Handwritten solution use torsion equation

A:

Q: The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof…

A: Given: The power, P = 300 kW The speed of shaft, N = 32 Hz The power at gear B, P1 = 120 kW The…

Q: A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D…

A:

Q: pulleys at -ach 400 mm ring and are own below. e shear stress of Pa, calculate the d for this raw…

A:

Q: 1. The solid line shaft in Fig. 1 is made of steel and transmits the input power of 35 kW at pulley…

A: The Answer is Below

Q: The end gear (closest to the journal bearing at A) is subjected to the loading shown in the figure.…

A: Given: The yields strength of material = 80 MPa

Q: 3. Knowing the rotation speed: n=300r/min and the power of applying on each wheel: P₁-200kW. P-50kW,…

A: Given Data: n=300 rpmP1=200 kWP2=50 kWP3=50 kWP4=100 kWτall=120 MPaLAB=LBC=LCD=1.5 mR=20 mm   To…

Q: PROBLEM NO. 1 A 40-mm diameter, 533-mm length shaft is drilled, for a part of its length L₁, to a 20…

A: Given data: D=40 mmL=533 mmd1=20 mmd2=30 mmτ=80 MPaN=230 rpm Need to determine the maximum power…

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw…

A: Given, Gear A deliver 10KN Gear C deliver 15KN A shaft carrying 3 gears that rotates at 1150 rpm…

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power to a…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.