The driveshaft of an automobile is being designed to transmit 203 hp at 2940 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 7800 psi.

The driveshaft of an automobile is being designed to transmit 203 hp at 2940 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 7800 psi.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A drive shaft to the blades of a helicopter transmits 800 kW at 200 rev/min. Neglecting transmission losses; determine the minimum external and internal diameters of the hollow circular section aluminum alloy shaft, when the maximum permissible shear stress in the shaft is limited to 30 MPa. It may be assumed that the external diameter of this shaft is twice its internal diameter. What will be the resulting angle of twist of this shaft over a length of 2 m, given that the modulus of rigidity, C 26900MPA.
The composite shaft shown consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 164 mm and a wall thickness of 7 mm. Steel pipe (2) has an outside diameter of 114 mm and a wall thickness of 6 mm. Both pipes are 3-m long and have a shear modulus of 80 GPa. If a concentrated torque of 20 kN-m is applied to flange 8, determine the torque in pipe (1). ... 3 m 3 m 20 kN-m (1) (2) B A 10.98 kN-m в) 15.63 kN-m 9.40 kN-m 14.85 kN-m
A steel core is bonded firmly to the copper tube (shell) to form the shaft shown. The length of the shaft is 450 mm and the end A is fixed to the wall. Take the shear modulus of steel and copper as 76 GPa and 38 GPa, respectively. The diameter of the core is 60 mm and the outer diameter of the shaft is 100 mm. Determine the maximum external torque (Tmax) so that the absolute maximum shear stress for any point H on the surface of the copper shell does not exceed 50 MPa. 450 mm A 100 mm 60 mm В Tmax =? kN · m
A solid steel shaft has a diameter of d and a length of L had used to transmit a power of 120 kW at 300 r.p.m. It was recommended that the maximum shear stress and angle of twist are limited to 60 MPa and 1.5 degrees respectively. Determine the diameter and length of the shaft. For the shaft material, G= 80 GPa.
A flat key is to be designed for 100 mm diameter shaft which will transmit 200kw at 300 rpm . If the allowable shearing stress is 300 Mpa and key width is 10 mm ,determine the length of key.
A circular hollow shaft has outer diameter of 60 mm and thickness of 15 mm and is subjected to a torque load of 4.2 kN•m. Determine the resulting minimum shear stress. Also determine the resulting maximum shear stress.
3. A solid circular shaft is 1.8 m and is made of steel with G = 70 GPa. When rotating at w = 70 rad/s, it transmits 28 kW of power from engine A to generator B. As the design engineer, you are asked to: (a) Determine the shaft's smallest allowable radius if the allowable shear stress is T allow = 80 MPa. (b) Determine the shaft's smallest allowable radius If the allowable angle of twist is allow = 0.1 rad (in other words, the shaft is restricted not to twist more than 0.1 rad). (c) If both conditions (a) and (b) are required simultaneously, which radius will you select as the allowable radius. (In other words which condition controls the situation)? Briefly explain your answer. (1 kW = 1000 Watts) B
No gpt, 1ly handwritten
A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75 in. Determine the torsional shear stress developed in the shaft.
A solid shaft (100 mm diameter) transmits 75 kW at 150 rpm. Determine the value of maximum shear stress set up in the shaft and the angle of twist per metre of the shaft length if G=80 GN/m².
Determine the maximum shearing stress (MPa) in a solid shaft of 60-mm diameter as it transmits 91 kW at a speed of 175 rpm.
A composite shaft is comprised of an inner solid steel shaft 1/6 ft in diameter slipped over with a hollow bronze shaft of 1/4 ft outer dimater and 1/6 ft inner diameter and of the same length as the steel shaft. The two shafts are then fastened rigidly together at their ends. For steel, G = 12 × 106 psi, and for bronze, G = 6 × 106 psi. What torque can be applied to the composite shaft without exceeding a shearing stress of 12,000 psi in the steel or 8,000 psi in the bronze?