Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation speed of 300 rpm where the diameter of the shaft AB and CE are 10 mm and 15 mm, respectively. The allowable shearing stress is 1 GPa with F.S. of 1.2 for both shafts. Neglect the deformation of the cable at E.  Where:  Radius of the gear at B, rB = 100mm Radius of the gear at C, rC = 150mm

Q: as a diameter of 2 in. and a thickness of 0.20 in. Disk B is supplied with 15 hp of power of which A…

A:

Q: Q2. The two shafts are made of steel. Each has a diameter of d mm, and they are supported by…

A: given data: diameter(d)=45mm G=70GPa=70*103MPaT=150NM=150*103N-mm(anticlockwise) lets take angle of…

Q: 1. If the power generated is 10 kW, determine the minimum allowable angular velocity of the shaft…

A: Given data: d=20 mmτ=60 MPa Need to determine the minimum allowable angular velocity of the shaft…

Q: (a) A circular shaft used for transmission is 510mm in length and 50mm in external diameter. It is…

A:

Q: 2. The circular shaft has fixed supports at both ends, points A and D. Determine the torque that…

A:

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: According to the given dataWe need to findminimum required diameter for the segments 1 and 2

Q: Two solid steel shafts of different diameters are joined together at point C. The diameter of the…

A:

Q: Need complete solution. The given planetary gear system is composed of 3 Planetary Gears C, Ring…

A: Given: The allowable shear stress = 100 MPa The frequency of shaft A, NA = y = 20 Hz The diameter of…

Q: The horsepower input of the power screw. The efficiency if the weight loaded is 10 kN.

A: This is consisting of Two threads twisted together in which the pitch is equal to twice the distance…

Q: Problem 5-57: The turbine develops 150 kW of power, which is transmitted to the gears such that C…

A: Given data as per the questionpower developed =150 kwdiameter of shaft =100 mm =0.1 mRotational…

Q: flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and…

A: The diameter of bigger circle is The diameter of smaller circle is The number of bolts on bigger…

Q: The torque of 250 kN.m produces a maximum shear stress of 48 MPa in the 8 m-long hollow steel shaft.…

A:

Q: Two steel springs with plain ends are arranged in series and supports a load. The upper spring has…

A:

Q: Two shafts are connected by gears. The diameter of the two shafts is 1.5 in. They have the same…

A: Given: Diameter of two shafts (D)=1.5in  or 0.125ftShear modulus G=11.2×106Radius of gear E=4in or…

Q: he shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if…

A: ⇒given data;⇒shear modulus(G)=75GPa                          =75*103MPa⇒angle of twist for gear…

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

A:

Q: A steel shaft is fixed at A and is subjected to the torques as shown. Segment AB has a diameter of…

A:

Q: PROBLEM 2 The two steel shafts are connected by gears D and C. Shaft AC is 4.0in in diameter while…

A:

Q: 303. Á steel shaft with a constant diameter of 50 mm is loaded as shown in Fig. 3-5 by torques…

A: Given                 Diameter, d = 50 mm                                    = 0.05 m Modulus of…

Q: Completely solve and box the final answer. Write legibly Determine the maximum mass (kg) can be…

A:

Q: the torque acting on the shaft; ii) the required external and internal diameters for the shaft;…

A:

Q: Two steel springs with plain ends are arranged in series and supports a load. The upper spring has…

A:

Q: d3 T3 T2 T1 d1 TP. B L3 L2 L1.-

A: The polar moment inertia of a circular cross-section is defined as moment of area about the axis…

Q: 2. The diameters of the solid shafts are: AB is 0.6 in, BC is 0.75 in. and CD is 0.9 in. The applied…

A:

Q: If T = 600 Nm, determine the absolute maximum shear stress in the shaft (in MPa) b. If the maximum…

A:

Q: The motor A delivers 7500 kW to the shaft at 3600 rev/min, of which 2500 kW is removed by gear B and…

A:

Q: pulleys at -ach 400 mm ring and are own below. e shear stress of Pa, calculate the d for this raw…

A:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 13…

A: For solving this problem, we have used torosion equation, answer we got after equating all the…

Q: The electric motor keeps the aluminum shaft ABCD, with rigidity modulus 27 GPa, operating at a…

A:

Q: Problem 2: A steel tube having an outer diameter of 2.5 in. is used to transmit 10 hp when turning…

A: Given:D=2.5 inP=10 hpN=30 rpmζallow=12 ksi

Q: 8 Q2: A shaft is driven by a motor which exerts a constant torque while the load taken off the shaft…

A:

Q: PROBLEM NO. 1 A 40-mm diameter, 533-mm length shaft is drilled, for a part of its length L₁, to a 20…

A: Given data: D=40 mmL=533 mmd1=20 mmd2=30 mmτ=80 MPaN=230 rpm Need to determine the maximum power…

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: The two shaft

A: Design of shaft is important process in any mechanical system. Design of shaft is determined by…

Q: Draw the intemal torque diagram .

A:

Q: Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation…

A: Calculated maximum mass(kg) that can be lifted at E.

Q: he motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and…

A: Shearing stress is created in a shaft when it is exposed to torque or twisting. Shear stress varies…

Q: The 43-mm-diameter shaft is subjected to the torques shown. What is the angle of twist of end A with…

A: The given shaft can be drawn as, Free body diagram of CB and AB can be drawn as,

Q: The shaft is fixed at ends A and B and has a positive torque T a distance of 4m from A and 8m from…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.