Completely solve and box the final answer. Write legibly Determine the maximum mass (kg) can be lifted at E if the 10-HP motor A has a maximum rotation speed of 300 rpm where the diameter of the shaft AB and CE are 10 mm and 15 mm, respectively. The allowable shearing stress is 1 GPa with an F.S. of 1.2 for both shafts. Neglect the deformation of the cable at E. Where: Radius of the gear at B, rB = 100 mm Radius of the gear at C, rC = 150 mm

Q: as a diameter of 2 in. and a thickness of 0.20 in. Disk B is supplied with 15 hp of power of which A…

A:

Q: 1. If the power generated is 10 kW, determine the minimum allowable angular velocity of the shaft…

A: Given data: d=20 mmτ=60 MPa Need to determine the minimum allowable angular velocity of the shaft…

Q: A rotating shaft carries three unbalanced masses of 4 kg, 3 kg, and 2.4 kg at radial distances of 75…

A:

Q: . A thin plate is composed of four CST elements, as shown inthe figure below. The plate is subjected…

A: I have attached the image below Explanation:

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: According to the given dataWe need to findminimum required diameter for the segments 1 and 2

Q: Need complete solution. The given planetary gear system is composed of 3 Planetary Gears C, Ring…

A: Given: The allowable shear stress = 100 MPa The frequency of shaft A, NA = y = 20 Hz The diameter of…

Q: The worm gear rotating at 1250 rpm drives a worm wheel and whose velocity ratio is 12 to 1. A…

A:

Q: The horsepower input of the power screw. The efficiency if the weight loaded is 10 kN.

A: This is consisting of Two threads twisted together in which the pitch is equal to twice the distance…

Q: Determine the brake horsepower of a round steel shaft with a torque of 17.5 in-lb running at 1800…

A:

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A:

Q: Problem 5-57: The turbine develops 150 kW of power, which is transmitted to the gears such that C…

A: Given data as per the questionpower developed =150 kwdiameter of shaft =100 mm =0.1 mRotational…

Q: The external torque on a drill bit varies linearly to a maximum intensity q, in.Ib/in . If the drill…

A:

Q: 2. The hollow shaft used in the system has the following conditions: B Outer Ø: 110 mm Ø Allowable…

A: Shear stress-induced in the shaft at any location (r) from the center is given by,= = 11/12Where, r…

Q: A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: The loads illustrated produce concentric axial force in the 20-mm-diameter shaft, which is made of…

A:

Q: Completely solve and box the final answer. Write legibly Determine the maximum mass (kg) can be…

A:

Q: 1. The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the…

A:

Q: The polar modulus for a solid shaft of 40 mm diameter is

A:

Q: Determine the maximum mass (kg) that can be lifted at E if the 10-HP motor A has a maximum rotation…

A: Please find the solution below

Q: the diameter of solld snaft (2) IS E. 72 teeth 30 teeth (1) (2)

A: Givenspeed of motor NA=808rpmZA=24ZB=72ZC=30ZD=60

Q: והו והו

A: Given as, ρm =14kwρA =3kwρB =5kwρC =6kwN=52rps

Q: A 500 mm pulley running at 400 rpm drives another pulley of the same diameter by means of a 12 mm…

A:

Q: The Smm module with 40 number of teeth gear is used to transmit 42.3 kw power at 350 rpm .Find the…

A:

Q: 4.The number of teeth in gears 1 and 2 are 60 and 40; module = 3mm; pressure angle = 20° and…

A:

Q: pulleys at -ach 400 mm ring and are own below. e shear stress of Pa, calculate the d for this raw…

A:

Q: 1-)The diagram of the change of cutting force for the cutting work performed with the press seen in…

A: Given data   Engine revolution =  900 rpm Flywheel revolutions = 60 rpm. Themoment of inertia of…

Q: 8 Q2: A shaft is driven by a motor which exerts a constant torque while the load taken off the shaft…

A:

Q: PROBLEM NO. 1 A 40-mm diameter, 533-mm length shaft is drilled, for a part of its length L₁, to a 20…

A: Given data: D=40 mmL=533 mmd1=20 mmd2=30 mmτ=80 MPaN=230 rpm Need to determine the maximum power…

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.