1-)The diagram of the change of cutting force for the cutting work performed with the press seen in the figure is given in the figure Engine rev the number is 900 rpm and the number of Flywheel revolutions is 60 rpm.The moment of inertia of the rotating masses in the engine is 0.35 kgm^2. Speed calculate the moment of Flywheel inertia required for the press so that its smoothness is 0.01 . Engine power is 1.5 kW it is known

Q: The flywheel in Figure.3 has moment of inertia of 33.5 ??. ?2 rotates at 365 rpm. A second flywheel…

A: Given: The moment of inertia of flywheel 1, I1 = 33.5 kg.m2 The moment of inertia of flywheel 1, I2…

Q: A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure…

A: We have to solve above question  Given data  Pitch diameter =50mm Power =3kw Angular velocity =200…

Q: For the drum brake shown in the following figure, there is an inner rim diameter of 280 mm and…

A:

Q: If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm…

A:

Q: angular acceleration of

A: Data we have  The speed of motor =Nm = 3200 rpm Angular acceleration of pump = α p  Angular…

Q: following figure shows a belt braking system operating on a brake drum for a lifting mechanism. It…

A:

Q: (Q2) The following data are given for the drum brake shown in figure (1) • Drum diameter is 400mm •…

A:

Q: 6. Four cylinders rolling in opposite directions has a speed ratio of AB.C:D = 5:2:3:4. If center…

A: Let the diameters of each cylinders be - DA, DB, DC and DD . The center distance is given by -DA2+…

Q: at distances of 100 mm from the central plane of the middle eccentric, find the amount of he masses…

A:

Q: Find the brake power of the engine running at 755 rpm. The iength of lever from centre of pulley is…

A: We need to figure out how much braking power the engine has at 755 rpm.The lever is 1.43 metres long…

Q: The rotor in the figure turning I and II formed in the beds imbalances and their angles are saving:…

A:

Q: The value of curvature correction factor k, will be if the spring index is 6. O a. 1.33 O b. 1.08 O…

A:

Q: A pulley 500 mm diameter is driven at 375 rev/min by a belt 200 mm wide by 12 mm thick. The tension…

A:

Q: (machine dynamic)  The variation diagram of the cutting force of the cutting work done with the…

A:

Q: A mono-cylinder engine  has r = 0.3 m, l = 0.9 m, It has: crank mass m2 = 4.5 kg , crank rG2 = 0.4r,…

A: Given that:  r = 0.3 m l = 0.9 m  crank mass m2 = 4.5 kg , crank rG2 = 0.4r conrod mass m3 = 12 kg…

Q: A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum.  The 48V…

A: GIven data: The diameter of the drum is d=10 in The weight attached to the cable is Ft=500 lb The…

Q: the efficiency is

A: Given; In order to test the efficiency of reducer gear train, input is given as, 1 kWAt the end of…

Q: Ex. # 5) Pinion 2 in the figure runs at 1 750 rpm and transmits 2.5 kW to idler gear 3. The teeth…

A:

Q: A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure…

A: Given:Power=3 kWpitch diameter=50 mmangular velocity of gear=200 rad/spressure angle of…

Q: An eccentric cam has diameter of disc 80 mm and an offset 30 mm from centre of rotation, operates a…

A: We have a flat faced follower that is operated by an eccentric cam with a disc diameter of 80 mm and…

Q: Calculate the indicated power of a cylinder and the engine, if the mechanical efficiency of the…

A: Given data: d=500 mmL=2050 mmNmax=124 rpmNmin=99 rpmPm=19.5 barnmin=5nmax=8 Need to determine the…

Q: For the gear mechanism in the figure: P1 = 4 kW, η1 = 1000 rpm, z1 = 18, z2 = 36, z3 = 54, z4 = 108,…

A: This question is solved with the help of gear ratio formulae.  Torque on gear 1,…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Brake is a mechanical device that absorbs energy from the moving system or any mechanism with the…

Q: 500 rpm, the follower is to be held against the cam by a helical compression spring with a force…

A: Given data- 1.cam running at =500 rpm 2.force on helical spring =80 lb-160 lb  355.8 N-711.7 N…

Q: A 257x 457.2 mm single acting engine runs at 200 rpm and makes 90 explosions per minute. The gross…

A:

Q: per hr at 20°. Determine the unit weight of be ufficient to give 33.5 m horizontal center-to-ce e to…

A:

Q: In the design in the figure, a force of Fn=45992 N acts in the vertical plane on a machine element…

A:

Q: An engine has a turning moment diagram with the areas above and below the mean torque line of  -50…

A: Given Data:   Area and its conversions are given to find out the change in energy.…

Q: i need the answer quickly

A:

Q: 5. What do you understand by 'fluctuation of energy' and 'maximum fluctuation of energy'. 6. Define…

A:

Q: Imagine two gears in mesh, the pinion is rotating clockwise, what is the force analysis for such a…

A: Explanation: The pinion is rotating clockwise and connected with the gear. Assume the gear us spur…

Q: el. 00

A:

Q: Q2/ A compound steam engine develops 250 kW at 80 r.p.m. The coefficient of fluctuation of energy as…

A: given data power= 250kw speed = 80rpm fluctuation of energy = 0.15 fluctuation of speed = 1% radius…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.