Problem 6 only, solve carefully, include the units in every step and draw the diagram. Thanks!Four cylinders rolling in opposite directions has a speed ratio of A:B:C:D = 5:2:3:4. If center distance between cylinderA and D is 80 inches, find the diameter of all cylinders 4. A steel tie rod on bridge must be made to withstand a pull of 5000 Ibs. Find the diameter of the rod assuming a factor ofsafety of 4 and allowable stress of 14,000 psi.5. A hollow shaft transmits 10 kW and running at 650 rpm with a shearing stress of 55 Mpa. The outside diameter is 1.2times that of the inside diameter. Find the inside and outside diameters in mm.6. Four cylinders rolling in opposite directions has a speed ratio of A:B.C:D = 5:2:3:4. If center distance between cylinderA and D is 80 inches, find the diameter of all cylinders.7. A steel 0.6 inch x 1.2 inch steel 90 m long is subjected to a 45kN tensile load along its length. If poison's ratio is 0.3.FindA. The deformation along its length, inchesB. The deformation along its thickness, inchesC. The deformation along its width, inchesD. The lateral strains, inches

Let the diameters of each cylinders be - DA, DB, DC and DD . The center distance is given by -DA2+…

Answered: 6. Four cylinders rolling in opposite…

6. Four cylinders rolling in opposite directions has a speed ratio of AB.C:D = 5:2:3:4. If center distance between cylinder A and D is 80 inches, find the diameter of all cylinders.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Similar questions

A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A steel shaft is transmitting 55 hp at 1200 rpm. The nature of the load and the type of service of the shaft is such that the allowance shearing stress based on the pure tension is 4000 psi. (MAXIMUM TORSIONAL STRESS AND ANGLE OF TWIST FOR A SOLID SHAFT) Calculate the diameter of the shaft to the nearest commercial size of the shafting. 2.Calculate the torsional deflection of the shaft in degree for one foot length of the shaft.
Need correct solution Don't copy .
PLEASE ANSWER NUMBER 3.43 MECH 222: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
A hollow shaft has an inner diameter of 0.035m and outer diameter of 0.06m. Compute for the torqueif the shear stress is not to exceed120 MPa in N-m.
The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted. Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5. Q3 a) An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N- m. Assuming that the shafts are subjected to torsion only, find the diameter of the shaft and the pin. The allowableshear stresses for the shaft and pin may be taken as 55 MPa and 30 MPa respectively.
Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to a torque of 800N-m.
Compute the torsional shear stress in a circular shaft with diameter of 50mm that is subjected to a torque of 800Nm.
A 4-spline shaft and to slide when not under load has a diameter of 2.5 in. Find the compressive and shear stresses if shearing force is 2500 lbs. If hub length is 2 inches.