(Q2) The following data are given for the drum brake shown in figure (1) • Drum diameter is 400mm • Width of the shoe is 75mm • The coefficient of friction is 0.24 • The maximum pressure is 1MPa. • The drum rotates 3000rpm in counter clock wise direction. • The equivalent polar moment of inertia is 10 kg.m/s? Determine the minimum actuating force and the frictional torque. What is the time required for deceleration to the rest?

(Q2) The following data are given for the drum brake shown in figure (1) • Drum diameter is 400mm • Width of the shoe is 75mm • The coefficient of friction is 0.24 • The maximum pressure is 1MPa. • The drum rotates 3000rpm in counter clock wise direction. • The equivalent polar moment of inertia is 10 kg.m/s? Determine the minimum actuating force and the frictional torque. What is the time required for deceleration to the rest?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

31
A В X Figure 3 Refer to Figure 3. A slender rod of mass 1.5 kg and length L = 1 m is pivoted at one end as shown. It is released from rest in a horizontal position and swings freely. At the instant it is released the angular acceleration (alpha) is 14.715 rad/s^2. In the question that follows, select the answer that is closest to the true value. What is the force reaction at the pivot in the y-direction at the instant the rod is released (when it is still horizontal) in units of N ? Answers: A) 3.68 B) 4.91 C) 6.13 D) 7.36 --- O A O B O D
Fig Q1 shows a two-stage spur gearbox. The input shaft is coupled to a motor. The shaft "b" turns freely in bearings C and D, except for the gear-tooth forces. Assuming 100% gear efficiency, determine the resultant radial loads applied to bearings C and D, and sketch the shaft "b" as a free body in equilibrium.
Asap
Calculate the indicated power of a cylinder and the engine, if the mechanical efficiency of the engine is given as 75 % Calculate the brake power and friction power of the engine. Provide your answer in kW and hp. Study the power if the engine is a four stroke type. Cylinder bore 500 Piston stroke 2,050 Stroke/bore ratio Speed range Mean effective pressure = 2050/500 124-99 19.5 Maximum cylinder pressure Numbers of cylinders 5 to 8 Feedback: Correct answer = 155 mm mm rev/min bar bar
A 2:1 speed reduction drive (Fig Q4) between two parallel shafts at 1200 mm centre distance is being provided by a V-belt of mass 0.5 kg/m. The diameter of the driving pulley is 200 mm and the driving shaft rotates at 900 rev/min. The driven pulley is 400 mm diameter. The angle of the pulley grooves is 40°, and the coefficient of friction between belt and pulleys is 0.35. If the maximum beit tension is 400 N determine: (i) The linear belt speed and the centripetal tension due to that belt speed. (ii) The angle of lap on each pulley (iii) The maximum power that may be transmitted Ø200 1200 Ø400
3.39 In Figure P3.9, 0 = 135° and @n = 10 rad/s. Draw and dimension the velocity polygon. Identify the follower velocity and the sliding velocity. Use the scale 1 in %3D 5 in/s. r= 2 in Follower 2 C 0,C = 1 in B on 1 B2 on 2 Cam 0 FIGURE P3.9
The Wright Brothers designed an engine and propeller that would produce enough forward motion to lift a simple light airplane. The 3 meter diameter blade rotated at a constant 330 rotations per minute (RPM). How does the RPM of the tip of one blade compare to the RPM of the middle of the one blade (halfway towards the center of the propeller)? The RPM is twice as much. The RMP is the same. The RPM is half as much. The RPM is one quarter as much.
Explain the Schematic Diagram in this problem. (tanginamo1 is the problem) and (tanginamo2 is the schematic diagram) Provide a reasonable explanation, thank you!
Do in 2 min
Solve with proper explanation
There are two pairs of closed soft tooth surface spur gears A and B Parameters of A: modulus m = 2mm, number of teeth Z, = 40,Z, = 90, width of teeth b =60mm. %3D Parameters of B: modulus m = 4mm, number of teeth Z, = 20,Z, = 45, width of teeth b = 60mm. %3D The accuracy of the two pairs of gears is grade 8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason?