והו והו

Q: 37. What factor of safety is needed for a 1.998 in diameter shaft with an ultimate * strength of…

A:

Q: A static shaft is subjected to torques at A, B, and C. It has a diameter of 58 mm and is made from…

A: The magnitude of angle of twist is The length of shaft  1 is The length of shaft 2 is The diameter…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: According to the given dataWe need to findminimum required diameter for the segments 1 and 2

Q: Determine the minimum shaft diameter at locations A, B, C, D, & E for an enclosed industrial…

A:

Q: Need complete solution. The given planetary gear system is composed of 3 Planetary Gears C, Ring…

A: Given: The allowable shear stress = 100 MPa The frequency of shaft A, NA = y = 20 Hz The diameter of…

Q: The bearing pad consists of a 150 mm by 150 mm block of aluminum that supports a compressive load of…

A: Given:A=150 mm x 150 mmP=6 KNθ=30°

Q: Q-1 The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The…

A:

Q: 2. In the gear system shown, the motor applies a torque of 600 N-m to the gear A. Shafts (1) and (2)…

A:

Q: 695 Ib.ft 1100 lb.ft 955 lb.ft D 550 lb.ft -4 ft- B - 5 ft A

A:

Q: Determine the brake horsepower of a round steel shaft with a torque of 17.5 in-lb running at 1800…

A:

Q: C 8 10 Determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a…

A:

Q: In the gear system of Figure 4, a torque of 5 N-m is applied on gear E. Shaft (1) and shaft (2) are…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: The composite shaft below, consists of three sections, a tubular indication welded, through flanges…

A:

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: he shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if…

A: ⇒given data;⇒shear modulus(G)=75GPa                          =75*103MPa⇒angle of twist for gear…

Q: 300 N-m 500 N-m The solid 30-mm-diameter shaft is used to 200 N-m transmit the torques applied to…

A: It is required to determine maximum shear stress

Q: An aluminum shaft with a constant diameter of 50mm is loaded by torques applied to gears shown.…

A:

Q: The loads illustrated produce concentric axial force in the 20-mm-diameter shaft, which is made of…

A:

Q: 8.10 Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in…

A: Given: Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed (N)=750rpm Power=4.6kW…

Q: 3. Gear B supplies 20 KW of power, while gears A, C and D withdraw 6 kW, 4 kW and 10 kW,…

A:

Q: Completely solve and box the final answer. Write legibly Determine the maximum mass (kg) can be…

A:

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A:

Q: the diameter of solld snaft (2) IS E. 72 teeth 30 teeth (1) (2)

A: Givenspeed of motor NA=808rpmZA=24ZB=72ZC=30ZD=60

Q: Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below.…

A: Consider the given figure. For the shaft AB, in equilibrium condition the torque acting on the gear…

Q: The steel shaft with two different diameters rotates at 4.3 Hz. The power supplied to gear C is 48.5…

A:

Q: The approximate distance between the two parallel shafts is 1500 mm. The shafts are to be connected…

A:

Q: The electric motor keeps the aluminum shaft ABCD, with rigidity modulus 27 GPa, operating at a…

A:

Q: Q-1 The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The…

A:

Q: lied to gear Dof the gear train shown. The bearings shown allow the shafts to rotate freely.…

A:

Q: Draw the intemal torque diagram .

A:

Q: Determine the minimum shaft diameter at locations A, B, C, D, & E for an enclosed industrial…

A: The power transmitted by gear B, P1 = 25 hpThe number of teeth on gear B, Z1 = 24The diametral pitch…

Q: Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation…

A: Calculated maximum mass(kg) that can be lifted at E.

Q: Problem 5-49: The splined ends and gears attached to the A992 steel shaft are subjected to the…

A: The diameter of the shaft, (d)=40 mmFor A992 steel we take the value of shear modulus, (G)=75…

Q: supplies a torque of The motor shown in Fig. 500 N· m to shaft BCDE. The torques removed at gears C,…

A: To find the torque transmitted by transverse cross-sections in BC,CD and DE of the shaft TBC=? TCD=?…

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.