Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12 in. A concentrated load of 60 lbf is then applied vertically downwards at a point 4 in. from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E = 29,000 ksi.

Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12 in. A concentrated load of 60 lbf is then applied vertically downwards at a point 4 in. from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E = 29,000 ksi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.4.22P: , Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14...

See similar textbooks

Related questions

Q: Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the…

Q: Problem 2. The assembly consists of three titanium (Ti- 6A1-4V) rods and a rigid bar AC. The…

Q: If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d…

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

Q: he bent pipe has a 1.5-in. outer diameter and a 0.2-in. wall thickness. Calculate the largest shear…

A: Let us draw the Free body diagram

Q: BLEM NO 1: The lower ends of the three bars are at the same level before the rigid homogenous 18…

Q: Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.5…

Q: The steel end-cap is fitted into grooves cut in the timber post. The working stresses for the post…

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.
A steel rod having a length of 50 m is suspended vertically from one end. It supports a tensile load of 250 kN at the lower end. The unit weight of the steel is 7,850 kg/m3. The allowable tensile stress for steel is 140 MPa. Use E= 200 GPa. Using the value obtained in the required diameter of the steel if its allowable stress is not exceed, Determine the deformation caused by the applied load? (mm)
Two vertical steel rods support the rigid bar as shown. Initially, the rods are stress-free. Given the data below, determine the stress of rods A and B after the 20 kN load is applied. Neglect the weight of the bar and use E = 200 GPa for steel. L= 3 m D = 3.5 mm A. Stress of rod A (MPa) B B. Stress of rod B (MPa) C. At what temperature AT change would the stresses for both rods be equal? Use a = 11.7 L= 4 m x 10-6 mm/mmC° (C°) D = 5 mm 4m 2m 2m 20 kN
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
The halves of the coupling are held together by four 5/8-in.-diameter bolts. The working stresses are 12 ksi for shear in the bolts and 15 ksi for bearing in the coupling. Find the largest torque T that can be safely transmitted by the coupling. Assume that the forces in the bolts have equal magnitudes. 0.5 in. 3.5 in.
Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the pulleys as shown in the figure, determine the angle of rotation of pulley D relative to pulley A. Use G = 28 GPa for aluminum. 600 N m 900 N m 1100 N m 800 N m 2 m 2 m 3 m
3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
For the assembly shown, determine the displacement of point B and D as the load of 50KN is applied at D. Rod BC is steel with length = 2m, A = 600mm2 E=200GPa. Bar ABD is rigid. What is the stress in the rod CB? What is the shear stress of the bolt of the pin at A if it's diameter is 20mm? B im Detail of the pin at A
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
The steel bars AC and BC, each of cross-sectional area 120 mm^2, are joined at C with a pin. Determine the displacement of point C caused by the 15-kN load. Use E=200 GPa for steel. (For Question No.1, what is the force on bar AB?) * A B 35° 35° 2.5 m 2.5 m 15 kN 13.778 kN
A spring sustains 200 ft-lb of energy with a deflection of 3’’. Assume that the mean coil diameter is 7 times the wire diameter and that the allowable stress is 100ksi. Determine the wire diameter.
The rigid wrench (not the brand Rigid sold at Home Depot!) shown is used to loosen a stuck nut at the top of a 4 mm radius smooth shafted bolt that is fixed supported at the base A. Determine the largest force F that can be applied if the bolt has a maximum shear stress of for this maximum torque value. G=75 GPa 18 MPa. Also determine the distance each force will move Ans: 6.03 N F. 150 mm 150 mm 80 mm