To decrease the amount of force needed increase the of the inclined plane. distance or length O power

Q: Determine the setting for a straight spur gear having 46 teeth of module 4 mm.

A: Given Data⇒ Straight spur gear : Number of teeth(t)=46 teeth Module(d)=4 mm

Q: 11. At injection pressure of 150 bar a spray penetrat ion af 25 cm in 20 milliseconds is obtained.…

A:

Q: The greater the distance, the less you need to exert to do work.

A:

Q: 1. In a turning operation, the diameter of the work- piece is 2 inches (50 mm), and it rotates at…

A:

Q: an advertising panel erected on uneven ground is supported by the EF and EG guy lines. If the force…

A:

Q: A steel cable with nominal diameter 25 mm as shown in Table Q2(a) is used in a construction yard to…

A:

Q: Q3 A car A is travelling along a straight path, while a lorry B is travelling along a circular path…

A: Given Data The velocity of car A is:VA=150+X=150+2=152 km/h The acceleration of car A is: aA=7000…

Q: U4.3 1 m A rectangular gate 1.6 m wide is used as a partition as shown. One side has linseed oil…

A:

Q: Which of the following is the best example of engineering control? A. noise-cancelling headphones

A:

Q: 2. Plot the root locus for the system shown below. Determine the range of gain K for stability. C(s)…

A: Given;The characteristic equation is.By R-H Criteria.    +     1100    +     72k0    +       0    +…

Q: 3. The liquids shown in figure (13-W1) in the two arms are mercury (specific gravity=13-6) and…

A: Data given-  Specific gravity = 13.6  Height of mercury column = 2 cm

Q: Q1 A horizontal beam BC is subjected to uniformly distributed load, w and at the same time it is…

A:

Q: >) In measuring the distance AB, the tape was not accurately levelled and that one end is 0.85 m…

A:

Q: The 25 kg crate A as shown in Figure Q1 rest on the smooth incline plane. At initial position the…

A: Given:-P=800 Nk=80 N/mθ=30°m=25 kgTo find:a) FBD of Ab) Net work donec) Velocity and accelerationd)…

Q: A piece of aluminum is pulled in tension from its original length of 202 mm with a stress of 172…

A:

Q: Q16. A mug is to be made from alumina. Which forming method would be most suitable?

A:

Q: For gear-and-shaft system shown, both shafts AB and CD have a diameter of 1.2 in. Pulley A is…

A:

Q: 2. Given: The piston rod of the hydraulic cylinder C imparts a constant acceleration to pin A of as…

A:

Q: (iii) What is the strain of brass rod of length 250mm which is subjected to a tensile load of 50kN…

A: Given : Length L= 250 mm load     P = 50 KN Change in length L1 = 0.5 mm

Q: A multi-fluid manometer shown in Figure 1 is used to measure the pressure in a water tank…

A:

Q: The lift of a wing, Fug, is a function of wingspan, W, chord length, H, surrounding air density, p,…

A: For solution refer below images.

Q: 2. An air conditioner using refrigerant-134a as the working fluid and operating on the ideal vapor-…

A:

Q: Determine the location of the shear center O of a thin-walled beam of uniform thickness having the…

A:

Q: Calculate normal and shear strains at the center

A:

Q: 4. A model for an airplane's pitch loop is shown below. Find the range of K that will keep the…

A:

Q: (b) Water flows from a pressurized tank through a pipe and rises to the surrounding as shown in…

A: For the given arrangement  A = 6 m, B = 3 m, h = 10 m   To determine  a)  The pressure in the tank…