The plates of thickness 1.5mm is joint by two 3.0mm diameter rivets as shown in the figure. Calculate the maximum safe load F that can be applied if the shearing stress in the rivets is limited to 10 MPa and the bearing stress in the plates is limited to 15 MPA. Assume the applied load is uniformly distributed among the two rivets. 10mm F

The plates of thickness 1.5mm is joint by two 3.0mm diameter rivets as shown in the figure. Calculate the maximum safe load F that can be applied if the shearing stress in the rivets is limited to 10 MPa and the bearing stress in the plates is limited to 15 MPA. Assume the applied load is uniformly distributed among the two rivets. 10mm F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can you help me with this
Refer to the figure. The steel rod is supported by an aluminum plate of 8 mm thickness. Force P pulls down the rod through the 12 mm hole in the aluminum plate. Neglect all weights of the rod and plate, and based on the design criteria that the maximum allowable shear stress in steel to be 18 MPa, calculate the allowable value of P in kN. Round to the nearest tenth. 10 mm T 12 mm- 40 mm- P 8 mm
For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch Maximum allowable shear stress of rivet = 96.53 MPa 3. Maximum allowable bearing stress of plate = 124.11 MPa %3D Yield Strength of the key = 45 MPa Ultimate Strength of the key = 128.5 MPa %3D Determine the maximum safe value of P that can be applied to both ends in Kips or Kilo pound. The figure below: 4 in P 7/8 in 7/8 in
The figure shows a flat hanger bar for supporting shop equipment in a factory. The bar is fixed to a support by means of a bolted connection. The main part of the hanging bar is 1.5 inches wide. This width varies up to 3.0 inches. A 1.0-inch diameter bolt transfers the hanger bar load to the two top bracket plates. Determine the allowable stress of the tension load P in the hanger in the following two instances: to. The allowable tensile stress in the main part of the hanger is 16,000 psi. b. The allowable stress load between the hanger bar and the bolt is 26,000 lb/pu.
15 kN 2) Two objects are glued on the angled plane as shown in figure. If the ultimate stress for the glued joint are 20 MPa and 10 MPa for tension and shearing stress respectively, find the value of 0 that corresponds to the maximum factor of safety and find the value of this maximum factor of safety. 0.035 m 0.05 m
The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin as shown. (Figure 1) Figure 1 of 1 > Part A If the wheel is subjected to a normal force of P = 3.3 kN, determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the wheel. Express your answer to three significant figures and include the appropriate units. Tavg= Submit Provide Feedback Value A Request Answer C Units ? Next >
2. For the joint shown in the figure, calculate: (a) The largest bearing stress between the pin and the members (b) The shear stress in the pin (c) The largest normal stress in the members 251N 25 AN 25 AN 25 AN
For the lap joint shown in the figure 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is limited to 60 MPa 2. Determine the safe load P which may be applied if the bearing stress of the plate Is limited to 110 MPa (4-20 mm diameter rivet) O O →P
two plates are fastened by a number of rivets and a tensile load of 300 KN is applied, find the number of rivets required if the shearing stress is limited by 65 MPa, and the bearing stress is limited by 95 ?MPa 300 KN 300 KN 125 mm 30 mm Dia. 25 mm 300 KN 25 mm 300 KN
The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20,000 psi? the 3/4 -diameter pin is in double shear.