Design a rivet that is utilized in a double riveted lap joint which connects two 10 mm thick plates. The applied load in the lap joint is 50 KN and the pitch is 60 mm. If the allowable stresses for the plate material are (tensile stress ot= 120 MPa, shear stress T= 90 MPa, bearing stress oc = 150 MPa) and for the rivet material are (tensile stress ot=130 MPa, shear stress t= 100 MPa, bearing stress oc = 140 MPa) e 8:09

Design a rivet that is utilized in a double riveted lap joint which connects two 10 mm thick plates. The applied load in the lap joint is 50 KN and the pitch is 60 mm. If the allowable stresses for the plate material are (tensile stress ot= 120 MPa, shear stress T= 90 MPa, bearing stress oc = 150 MPa) and for the rivet material are (tensile stress ot=130 MPa, shear stress t= 100 MPa, bearing stress oc = 140 MPa) e 8:09

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question: Consider that the fit between the elements shown in the Figure below is H6/s5. They are both made of SAE 1340 OQT 1000 steel (Sy= 950 MPa, E = 200 GPa). Take D; = 75 mm and D, %3D %3D 90 mm. Determine the maximum possible value of the tangential stress at the inner surface of the outer element in MPa. NOTE: Answer is not 4750MPA. If you Submit This answer I will Directly report. |D, H6/s5 D. 6/7
Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure below. The joint material has the following allowable stresses: tensile stress = compressive stress -50 Mpa, shear stress =35 Mpa and crushing stress = 90 Mpa. (Assuming: the load is applied statically). P- C1 78 mm C1 78 mm C2 C3 C3 156 mm 98 mm C4 C1 C5 C1 60 mm C4 C5 P. C5 C2
2. The bottom shell of a steel tanker is longitudinally framed. The spacings of transverse floor and longitudinal are 5 m and 0.8 m respectively. The bottom plating is 12 mm thick and the longitudinals are 150 x 10 mm flat bar. For higher- tensile steel, Young's modulus E = 210 kN/mm and yield stress oy = 340 N/mm?. Calculate the Euler buckling stress of the stiffened bottom panel and comment on the result. State any assumptions made. [342 N/mm]
The figure below shows a set of plates joined by a rivet, subjected to a force F of 22.5 kN. Considering that the rivet to be used must be able to withstand a shear stress of 100 MPa, and adopting a safety factor equal to 2, what is the smallest possible diameter of the rivet?
If the flat link shown below has an allowable tensile stress of 75 MPa, then a force P 1800 N will require the link to have a minimum thickness of: 30 mm 10 mm 3.20 mm 2.60 mm 2.40 mm 2.20 mm 3.60 mm 3.00 mm 2.80 mm O 3.40 mm
A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch a hole in a 1/4 in. plate. If a force P=20,000 lb is required, what is the average shear stress in the plate and the average compressive stress in the punch?
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
H.W Find the No.of rivets wanted to joint two plates type Double cover Butt joint ,the diameter of rivet is 20cm and the shear stress 200MN/m2 and tensile force 600OMN.
2. For the joint shown in the figure, calculate: (a) The largest bearing stress between the pin and the members (b) The shear stress in the pin (c) The largest normal stress in the members 251N 25 AN 25 AN 25 AN
Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 10 mm and an allowable normal stress of 70 MPa. Pipe (2) has an outside diameter of 44 mm, a wall thickness of 8 mm, and an allowable normal stress of 170 MPa. Assume x1 = 2.9 m, x2 = 1.9 m, and y1 = 4.3 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B (1) (2) Answer: Pmax i kN
1cm t1 (cm) P 3,2 cm t2 (cm) t1 (cm) 1 cm 20 cm Ь (ст) P = 20t %3D Dp=1,6 cm
4) The C-clamp shown below has rectangular cross-section A-A that is 33 mm tall by 12 mm wide and the material is class 50 gray cast iron. Determine maximum tensile stress and factor of safety for clamping force F = 3.2 kN. Ignore stress concentration factors. See Section 4.9 in Norton for help with curved beams. MPa N O MAX |F F 60 mm 40 mm 12 mm 33 mm 33 mm Section A-A A