A double riveted double cover butt joint in plate of (20) mm thick is made with (25) mm diameter rivets at (100) mm pitch. (Take tearing stress=(120) N/ mm2, Shear stress= (100) N/mm2, Crushing stress= (150) N/mm. Find the efficiency of joint? e 10:54

A double riveted double cover butt joint in plate of (20) mm thick is made with (25) mm diameter rivets at (100) mm pitch. (Take tearing stress=(120) N/ mm2, Shear stress= (100) N/mm2, Crushing stress= (150) N/mm. Find the efficiency of joint? e 10:54

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Related questions

Q: Determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gas…

Q: Design a single riveted lap joint to connect two mild steel plates, 14.5 mm thick, the joint being…

A: We will consider maximum shear stress criteria and maximum crushing stress criteria for the design,…

Q: (D) Seven circular cross-section rivets (Dia.=16 mm) are used to fix a lap joint of steel plates…

A: Given data: Total load (P) = 15 kN d = 16 mm E =80 GPa Need to…

Q: A welded joint of circular shaft as shown in figure is subjected to an eccentric load of 2.5 kN. If…

Q: ASAP

Q: 4. The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet…

Q: Example: The coupling shown in Fig. below is constructed from steel of rectangular cross-section and…

A: For the given coupling P = 50 kN dia of bolt (d) = 15 mm To determine (i) the shear stress in…

Q: 2. The lap joint in the figure is made using a 30 mm diameter bolt. The outer plates are 5 mm thick,…

Q: Design a rivet that is utilized in a double riveted lap joint which connects two 10 mm thick plates.…

Q: Solve the problems below: 1. The lap joint shown in Fig. P-126 is fastened by four 3/4 -in.-…

Q: 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is…

Q: A double riveted lap joint with chain riveting is to be made for joining two plates 10 mm thick. The…

A: Given Datat = 10mmσt = 60 mPaτ = 50 mPaσc = 80 mPaTo Find1) d2) P3) Pd4) n

Q: The figure below shows two plates connected by two rivets. The plates are made from aluminum 6061-T6…

Q: Design a triple riveted butt joint with equal double cover plates (zig-zag riveting) is used for The…

A: We have to solve and find Checked the efficiency of longitudinal and circumferential joints

Q: Q-1 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by four fillet…

Q: 4. Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using…

Q: (1) The figure shows a horizontal steel bar 3/8 in thick loaded in steady tension and welded to a…

A: Given data: b=2ind=2 inh=516int=38 inτallow=20 kpsi Need to determine the allowable force.

Q: 4. A double riveted lap joint with chain riveting is to be made for joining two plates 10 mm thick.…

Q: The figure shows a welded steel bracket loaded by a static force F. Estimate the load F if the…

Q: The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a…

A: Given data: b=49 mmd=48 mmh=5 mmτallow=148 MPa Need to determine the allowable force.

Q: The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet has…

A: Given data Diameter of rivet = 12 mm Thickness of plate = 15 mm Width of plate = 100 mm a) if load =…

Q: A. for the lap joint shown below, calculate the safe axial tensile force P if Otensile=136MP ,…

Q: Calculate the riveted joints, find its efficiency and draw a suitable sketch. Thickness of the…

A: Another name of rivet joint is lozenge joint. Selection of material σt=80 mpaζ=65 mpaσc=160 mpa

Q: for the lap joint shown below, calculate the safe axial tensile fo 126 102 A 220M

Q: For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch…

A: Given Diameter of each rivet =34 inch=18.796 mmMaximum allowable shear stress of rivet τy =96.53…

Q: 1cm t1 (cm) →P 3,2 cm t2 (cm) t1 (cm) 1 cm 中中 20 çm b (cm) P. →P P = 20t Dp=1,6 cm

Q: A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of fillet…

A: Torque (T) = 1000 Nm Shear stress (τ) = 160 MPa = 160×106 Pa

Q: The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a…

A: Allowable load F = 47458.18NF= 47.46 KNExplanation:

Q: A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is…

Question

A double riveted double cover butt joint
in plate of (20) mm thick is made with
(25) mm diameter rivets at (100) mm
pitch. (Take tearing stress=(120) N/
mm2, Shear stress= (100) N/mm2,
Crushing stress= (150) N/mm. Find the
efficiency of joint?
e 10:54

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spherical tank of diameter 48 in. and wall thickness 1.75 in. contains compressed air at a pressure of 2200 psi. The tank is constructed of two hemispheres joined by a welded seam (see figure). (a) What is the tensile load/ (lb per in. of length of weld) carried by the weld? (b) What is the maximum shear stress rm2Xin the wall of the tank? (c) What is the maximum normal strain e in the wall? (For steel, assume E = 30 X 10 psi and v = 0.29.)
Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
: A cylindrical tank with diameter d = 18 in, is subjected to internal gas pressure p = 450 psi. The tank is constructed of steel sections that arc welded circum fereiitially (sec figure). The heads of the tank are hemispherical. The allowable tensile and shear stresses are 8200 psi and 3000 psi, respectively. Also, the allowable tensile stress perpendicular to a weld is 6250 psi. Determine the minimum required thickness /minof (a) the cylindrical part of the tank and (b) the hemispherical heads.
(D) Seven circular cross-section rivets (Dia.=16 mm) are used to fix a lap joint of steel plates under single shear action. If the rivets are made from Aluminium (E=80 GPa) and the plates under tension of 15 kN. Solve this problem to show weather this joint is safe or not. Suppose all the rivets have equal load share.
Design a rivet that is utilized in a double riveted lap joint which connects two 10 mm thick plates. The applied load in the lap joint is 50 KN and the pitch is 60 mm. If the allowable stresses for the plate material are (tensile stress ot= 120 MPa, shear stress t= 90 MPa, bearing stress oc = 150 MPa) and for the rivet material are (tensile stress ot=130 MPa, shear stress t= 100 MPa, bearing stress oc = 140 MPa) e 8:09
For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch Maximum allowable shear stress of rivet = 96.53 MPa 3. Maximum allowable bearing stress of plate = 124.11 MPa %3D Yield Strength of the key = 45 MPa Ultimate Strength of the key = 128.5 MPa %3D Determine the maximum safe value of P that can be applied to both ends in Kips or Kilo pound. The figure below: 4 in P 7/8 in 7/8 in
Give me right solution with clear calculations
I need a quick solution within 15 minutes With put a happy emoji at the end my best wishes Hamoudi
Please answer the problem. Provide a free body diagram. Show the full, complete and clear solution.
4. A double riveted lap joint with chain riveting is to be made for joining two plates 10 mm thick. The allowable stresses are : o, = 60 MPa ; t = 50 MPa and o, = 80 MPa. Find the rivet diameter, pitch of rivets and distance between rows of rivets. Also find the efficiency of the joint. [Ans. d = 20 mm ;p= 73 mm; pb = 38 mm; n = 71.7%]