The box shown in the figure is assembled by gluing two pieces of plastic together at an angle a. The box has a rectangular cross section (a = 100 mm and b = 60 mm). The maximum allowable normal stress for the adhesive is 35 MPa, and the maximum allowable shear stress is 22 MPa. Using a Safety Factor of 1.5, determine: a. Largest allowable load P b. Angle a at this load

Q: which is given. What are the x and : coordinates of the bracket's mass cen- ter? (The angle 0 in the…

A: To Find :  The x and z coordinate of the bracket mass . Given :  The total number of hole is n=4 The…

Q: 4. The diameter of a circle has endpoints: (2, -3) and (-6, 5). Can you find the coordinates of its…

A: We know that if the endpoint of diameter of circle are p(x1, y2) and q(x2, y2)  Then it's center's…

Q: 3. Point B is known to be 711.202m from A at a bearing of 96°10'13". When viewed from a point P, the…

A: Given Information, AB = 711.202m   To convert an angle from minutes and seconds to a decimal value,…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Can you please draw Mohr's circle for the solution above?

A: Given that, σx=350 MPaσy=230 MPaτxy=-480 MPa

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: I have a cube fixture. Made from 6061-T6. Length is 12 inches, width is 12 inches, and height is 2…

A: Calculating the overturning moment of a static object placed on a flat surface, like your cube…

Q: Is 2.0cm3 of aluminum same as 2.0cm3 of lead

A: According to the given data, the volume of the aluminum object is 2.0 cm³  and the volume of the…

Q: E 12.5 m C А 8 m 5 m

A:

Q: please calculate at least 3 decimal places a) Draw a sketch where you replace the distributed…

A:

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

A:

Q: Can you pls slove this question briefly with hand written notes and diagram

A:

Q: Draw projections of this plane and find its inclination with the HP

A:

Q: 500 I In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R…

A: Solution:   According to the Cosine law, the Resultant of two concurrent, co-planar force system…

Q: I want to buy a two METAL SPUR GEAR for my 2 pieces of G.I pipe with an 3 inches diameter (3mm…

A:

Q: A steel collar has an inside diameter of 1-1/8 in., an outside diameter of 3-3/4 in., and a length…

A: Given: internal diameter Di = 1-1/8 = 9/8 inches outer diameter Do = 3-3/4 = 15/4 inches length =…

Q: OK, so the EA = 108 N, Length (L) = 13 m, and the angle is 22.6. What now?

A: Here you are asking about what to do if the EA = 108 N, Length (L) = 13 m, and the angle is 22.6…

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: f e (D d b C a k j a=38.0 b=41.5 c=39.3 d=40.1 e=55.8 f=39.4 q=36.7

A: a = 38.0b = 41.5c = 39.3d = 40.1e = 55.8f = 39.4g = 36.7h = 65.7i = 49.0j = 50.0k = 61.9l = 7.8m =…

Q: Solve the following differential equation: dy 2y – x*e-2x = 0 dx

A: