Q5/ If the No.of rivets wanted to joint two plates type Double cover Butt joint is 40 as shown in fig.5 with diameter of rivet is 10cm .Find the shear stress if the plates under tensile force 3000MN. Figure5

Q5/ If the No.of rivets wanted to joint two plates type Double cover Butt joint is 40 as shown in fig.5 with diameter of rivet is 10cm .Find the shear stress if the plates under tensile force 3000MN. Figure5

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.13P: Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses...

See similar textbooks

Similar questions

A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
A high-strength steel drill rod used for boring a hole in the earth has a diameter of 0.5 in. (see figure). The allowable shear stress in the steel is 40 ksi and the shear modulus of elasticity is 11,600 ksi. What is the minimum required length of the rod so that one end of the rod can be twisted 30º with respect to the other end without exceeding the allowable stress? If the shear strain in part (a) is limited to 3.2 × 10-3 , what is the minimum required length of the drill rod?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A tension member is to be constructed of two pieces or plastic glued along plane pq (see figure). For purposes of cutting and gluing, the angle ?? must be between 25 and 45. The allowable stresses on the glued joint in tension and shear are 5.0 MPa and 3.0 MPa, respectively (a) Determine the angle it so that the bar will carry the largest load P. (Assume that the strength of the slued joint controls the design.) (b) Determine the maximum allowable load ?? if the cross-sectional area of the bar is 225
An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with closed ends (see figure). The fabric and plastic structure is inflated by a small blower and has a radius of 40 ft when fully inflated. A longitudinal scam runs the entire length of the "ridge" of the structure. If the longitudinal scam along the ridge tears open when it is subjected to a tensile load of 540 pounds per inch of seam, what is the factor of safety n against tearing when the internal pressure is 0,5 psi and the structure is fully inflated?
Give me right solution with clear calculations
A double riveted single cover butt joint (zig zag arrangement), is used for connecting two plates 15mm thick. The diameter of the rivets is 20mm and the pitch is 100mm. Draw the joint with hand sketch and calculate the efficiency of the joint, if permissible stresses are as below: Permissible shearing stress in rivets = 120Mpa Permissible tensile stress in plate = 150MPa Permissible crushing stress in rivets = 210MPa
A double riveted lap joint with chain riveting is to be made for joining two plates 10 mm thick. The allowable stresses are : o, = 60 MPa; T= 50 MPa and o. = 80 MPa. Find the rivet diameter, pitch of rivets and distance between rows of rivets. Also find the efficiency of the joint.