Refer to the figure. The steel rod is supported by an aluminum plate of 8 mm thickness. Force P pulls down the rod through the 12 mm hole in the aluminum plate. Neglect all weights of the rod and plate, and based on the design criteria that the maximum allowable shear stress in steel to be 18 MPa, calculate the allowable value of P in kN. Round to the nearest tenth.

Refer to the figure. The steel rod is supported by an aluminum plate of 8 mm thickness. Force P pulls down the rod through the 12 mm hole in the aluminum plate. Neglect all weights of the rod and plate, and based on the design criteria that the maximum allowable shear stress in steel to be 18 MPa, calculate the allowable value of P in kN. Round to the nearest tenth.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
The state of plane stress shown occurs at a critical point of a metal machine component. As a result of several tensile tests, it has been found that the tensile yield strength is Fy for the grade of metal used. Determine the ratio of OT/ OH shown in the figure, using the maximum-shearing-stress criterion (Tresca Hexagon). (Using Mohr circle method to calculate principle and average stresses) OX TXy Mpa Mpa Mpa MPa ob σy тху 90 -60 45 310 dy OX x Sx=Sx Sy=sy txy=txy Fy=Yield Strength Answer
A circular rod with a diameter of 40.0 mm has a groove cut to a diameter of 35 mm. A full radius of 3.0 mm is produced at the bottom of the groove. Compute the maximum stress in the rod when an axial tensile force of 46 kN is applied.
A 28mm diameter steel shaft AB is built into a rigid wall at A and supported by a smooth bearing at B. The lever BC is welded to the end of the shaft. Load P 360 newton is applied as shown in the figure below. Determine the maximum shear stress and the angle of twist if the distance from A to B is 3 meters and the distance from B to C is .3 meters
A pin connection, like that shown in Figure -16, is subjected to a force of 16,5 kN. Determine the shear stress in the 12.0 mm diameter pin.
) A machine having a mass of 9555 kg is supported by three solid steelrods arranged as showed in the following figure. Each rod has a diameter of 50 mm. Compute the stresses in MPa in the three rods of AB, BC, and BD.
NEED ANSWER ASAP THANK YOUU The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 20144 lb is applied at A? The d = 0.79-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
20 FF 170 A 30 Ölçüler mm cinsindendir. A-A kesiti When the torture in the figure squeezes the material, the maximum force F in the clamping jaws is 1 kN. Calculate the maximum normal stress in section A-A according to the given?
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
3-103: A circular rod with a diameter of 10.0 mm has a groove cut to a diameter of 8.0 mm. A full radius of 1.20 mm is produced at the bottom of the groove. Compute the maximum stress in the rod when an axial tensile force of 5500 N is applied.
The steel bar shown has a 100 mm by 25 mm rectangular cross section. If an axial force of P = 180 kN is applied to the bar, determine the maximum normal stress (in MPa) acting in the bar. Note: Your submitted answer should not include units. 100 mm Answer:
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. I Determine the tensile stress in each rod. Determine the shear stress in pin A between the members. If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint. 40 mm 5 kN. 30 mm 25 mm 5 kN