A cylindrical tank with closed ends is filled with compressed air at a present of 450 MPa. The inner radius of the tank is 2 m and it has wall thickness of 8 mm. The magnitude of maximum in plane shear stress is.

Q: A frame of two members (AC) and (BD) are connected together at pin B. The other ends are pin-…

A: According to the information we have a frame with two members AC and BD that is pinned together at…

Q: Steel balls (diamęter = 21 mm, p= 7833 kg/m , k = 54 W/m-°C, Cp = 0.465 kJ/kg-°C, and a = 1.474x10 m…

A:

Q: The poison's ratio is the ratio between stress to strain Select one: True False

A: Poisson's ratio is the ratio of lateral strain to the longitudinal strain. The strain in the…

Q: A permanent bolted joint has four M24 ISO 8.8 bolts with coarse threads. The joint stiffness…

A: Answer: 136mm Solution is given below.

Q: An airplane is flying at a standard altitude of 16000 ft. with a velocity of 270 m/s. At a point on…

A: Given: The altitude of air plane, h = 16000 ft = 4.8768 km The speed of air plane, V1 = 270 m/s The…

Q: Midrange and alternating stresses becomes equal only for Reversed stress O Repeated stress None of…

A: Option B Repeated Stress

Q: The thermal efficiency of a reversible power cycle operating between hot and cold reservoirs is 50%.…

A: Given data:- Thermal efficiency of reversible power cycle =50% to find:- Coefficient of performance…

Q: m /s, v=1.798E-5 m/s, Pr= 0.7228). If the optimum spacing is 12 mm, what is the heat transfer rate…

A:

Q: Cavity flow is generated when a plate is dragged at speed U over the top of a cavity (of height 8)…

A: Given: To find: Fluid stretching and rotational components

Q: What is the pitch diameter for an M24 fine-series threaded bolt? O 21.5 mm

A: What is the pitch diameter for an M24 fine-series threaded bolt?

Q: For external forced convection with an isothermal surface, what is the Nu# correlation equation for…

A: Nusselt number (Nu) signifies the ratio of conductive resistance to the convective resistance…

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A: Take moment about the point E = 0

Q: Part Three: In the diagram at the right, ABC represents a post-beam system rotating about an axis…

A:

Q: (8.18) Water flows at a rate of 25 gallons per minute in a new hori- zontal 1.5-in.-diameter…

A:

Q: calculate the annual heating demand and the maximum heat output required by the boiler b) If the…

A: Given: Heating - 2670 DD/year V - 300 m3 U - 252 W/K To find: Design service heat loss

Q: 1. 100 mm The bar has a diameter of 60 mm. If it is subjected to the force components as shown in…

A:

Q: Fluid: Consider the following two tank system, where an input flow enters the first tank with…

A:

Q: A composite structure used for electrical cable ducting on an aircraft carrier is made by the…

A: In the problem, it was given the volume fraction of fibres Vf = 0.6, which means that 60% of the…

Q: 3. Knowing the rotation speed: n=300r/min and the power of applying on each wheel: P₁-200kW. P-50kW,…

A: Given Data: n=300 rpmP1=200 kWP2=50 kWP3=50 kWP4=100 kWτall=120 MPaLAB=LBC=LCD=1.5 mR=20 mm   To…

Q: •8-1. Determine the minimum horizontal force P required to hold the crate from sliding down the…

A:

Q: A gas turbine receives a mixture having the following molar analysis: 50% CO2, 10% H20, 40% N2 at…

A: Given Data: The temperature of mixture at the inlet is, T1=875 K. The pressure of mixture at the…

Q: Steam condensing at 120°C (h = 2203 kJ/kg) on the shell side of (1 shell and 12 thin- walled tubes)…

A:

Q: Hot fluid "C= 2562 J/kg.k , Pr=51.3, µ = 5.22E-3 Pa.s, k = 0.260 W/m.K" flows at 1.3 kg/min inside a…

A: Cp =2562 J/kg.K Pr = 51.3 Dynamic viscosity, u = 5.22*10-3 Pa.s k = 0.260 W/m.K Hot fluid mass flow…

Q: Question 1 An ideal-gas mixture consists of 2 kmol of N2 and 4 kmol of CO2. The gas constant (In…

A:

Q: 3-The flywheel of an internal combustion engine maintains the smooth rotary motion of the O (A)…

A: 1. The flywheel of an internal combustion engine maintains the smooth rotatory motion of the....…

Q: Quickly

A:

Q: A circular plate of diameter (2.20 m) is placed some how 1.5 meter above the room floor, if the…

A: Given Data:- Diameter (d) = 2.20 m Raleigh number (Ra) = 7.653 × 107 × d3 Temperature (∆T) = 73°C…

Q: Consider the following cases: Case 1: A rod with specified surface temperature. Case 2: A rod with…

A: Given:

Q: Exercice 1: Déterminer, par la méthode des sections (de Ritter), la force dans la membrure EF due…

A:

Q: A heat engine receives heat from a source at 1500 K at a rate of 600 kJ/s and rejects the waste heat…

A: As per the calculation the nearest option is 83%.

Q: Consider an insulated pipe exposed to the atmosphere, then the critical radius of insulation:

A: Heat exchange rate will proportional to the outside fluid’s (velocity squared) and also the inside…

Q: A cantilever beam of length 700 mm, width 55 mm and thickness 15 mm is made of steel with Young's…

A:

Q: A cross-flow heat exchanger with air mixed and oil unmixed, (C = 2150 J/kg. °C), the mass flow rate…

A:

Q: If rod CD is rotating with an angular velocity ocD. At the instant shown in the figure, which leter…

A:

Q: 7. Three Column of equal cross soction and of the same material support a rigid weightloss beam at…

A:

Q: A threaded screw specified by 1-in UNF will have: O d = 25 mm and p = 2 mm %3D O d = 1.0 in and N =…

A: 1-in UNF outer diameter of threads is 1 in. Total 12 turns at 1'' pitch value = 2.12mm

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.