Answered: Ex. 3. Determine the angle of the in-…

Ex. 3. Determine the angle of the in- clined tube shown in figure if the pres- sure at A is 7 kPa greater than that at B. (Ans. 0 = 23.86°) 0.3 m 0.5 m Oil Water 3 m Air B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q1: For the retaining wall shown below, and for the following values: • Plot the pressure diagram…

Q: In the setup seen in the image, an oil tank's central circular opening is sealed off by a solid…

A: Given: The specific gravity of mercury, SGm = 13.6

Q: determine the depth of water, h, in th

Q: A triangular plate shown in the figure is submerged in oil, specific gravity = %3D 0.8, 3.98 m below…

Q: 3) Gate AB in the figure is 1.2 m long and 0.8 m into the paper. Compute the force F on the gate and…

A: Given the gate Dimensions. Required- Force on the gate and centre of pressure.

Q: a. For U-tube manometer shown in the figure (a), fluid 1 is water and the gage fluid is mercury.…

A: As per the guidelines, I can solve only one question at a time and I can solve only first question.…

Q: Calculate the horizontal and vertical forces acting on the curved gate shown in the figure Calculate…

A: The figure below shows the schematic diagram of the Gate.

Q: Ex. 5. A weight lies on a piston with a radius r₂ = 1.0m. Determine the for- ce F₁ applied to the…

Q: Problem 2 Two open water tanks are connected through a manometer as shown in the figure below. (a)…

Q: Q3) Compute the horizontal and vertical components of the water pressure acting on the face of…

A: Given data: ● The included angle of tainter gate AB: θ = 72° ● The radius of the sector of the…

Q: Q3/ Two pipes containing water are connected to a compound differential manometer as shown in Fig.…

A: Given that: Specific gravity of the oil is 0.9. Specific gravity of mercury is 13.6 Therefore, ρw =…

Q: Three liquids of different densities fill connected tubes as shown in the figure below (not drawn to…

Q: 6. Determine the pressure difference between the water pipe and the oil pipe shown in the figure…

Q: Please be clear with your solution. Make an explanation for the formula and solution you used.…

A: To find normal force to be applied

Q: Find the force of oil on the top surface CD pon ping is reduced by 40 ft

Q: 2.) Given the two-compartment vessel shown in the figure. Gage A reads 85 psig: gage B inside…

A: Given data: - The reading of gauge A is (PA)g = 85 psig. The reading of gauge B is (PB)g = 25…

Q: 3-60. Calculate the difference in pressure between point A and B in the inclined pipeline of Figure…

Q: The cylinder shown in the figure extends 10 ft into the paper. If the cylinder has the radius of 4…

A: Length of the cylinder, L=10 ft Radius of cylinder, R= 4 ft Specific gravity of oil, s.g.=0.85

Q: bläi 5 In the Fig. below is shown the * cross-section of the tank full of water under pressure. The…

Q: Calculate the pressure difference between A and B for the set-up shown in the figure.

A: Given

Q: The pressure at point m in the figure shown was increased from 85 kPa to 125 kPa. This causes the…

A: Given DataPm1=85kPaPm2=125 kPaρm=13.6

Q: 1. Gate AB in Fig. below is 15 ft long and 8 ft wide into the paper and is hinged at B with a stop…

A: Length of the gate, L=15 ftWidth of the gate, w=8 ftThickness of the gate, t=1 in =112ftWater…

Q: 1.) An open tank is filled with three different columns of fluid shown in the figure. Fluid 1 is a…

Q: Equilibrium is reached as shown in the figure. Calculate the density of the unknown liquid in terms…

Q: For the tank shown in the Figure, h1 = 4.5m and h3 = 9.2m . Determine the value of h2.

A: Givenh1=4.5mh3=9.2mso=0.85

Q: The cylinder shown in the figure extends 10 ft into the paper. If the cylinder has the radius of 4…

A: From the given data,

Q: 4Psi Tank full of water Empty cylinder r= 4.5 ft

Q: A triangular plate shown in the figure is submerged in oil, specific gravity = 0.8, 3.37 m below the…

A: Specific gravity, SG= 0.8 h= 3.37 m Width of the triangle, b= 1.52 m Height of the triangle, d=…

Q: mm, what is the force P acting on the piston? The weight of the p Pitun Water Mereury

A: For solution refer below images.

Q: figure contains water to a depth of 1.4 m. Find the work required 4 m 6 m to pump all the water to…

A: Solution is attached below

Q: Problem 1. The gauge pressure of the air in the tank shown in the figure below is meası.red to be 65…

Q: lote: Use three decimal places and no need to input the unit. Figure the 20°C water and gasoline are…

A: This problem is the application of the pascal's law, which states that the the pressure at a point…

Q: The tank shown in the figure 4 is accelerated to the right. Calculate the acceleration a, needed to…

A: Given that width of tank =1m length of tank = 2 m air gap = 0.2 m

Q: Q1) If the vertical component of the hydrostatic force on the gate BC shown in fig.1 is 1200…

A: GIVEN DATA- A gate BC given we have to calculate all three point

Q: Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with…

A: Since the chambers are closed and the pressure in both the chambers must be same. we will transform…

Q: An inverted differential manometer is connected to two pipes A and B which convey water. The fluid…

Q: Q4//Determine the required vertical force F to be applied at the lower edge to open the square gate…

A: Area= 2.8×2.8 =7.84m2 Location of CG(y) =1.8+2.8sin45/2 =2.78m…

Q: QUESTION 3 When valve A is closed, the pressure difference between A and B is -27 kPa. (11) Find h…

A: Pascal's law states that on a given horizontal plane of static fluid, a fluid particle experiences…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Ex. 3. Determine the angle
of the in-
clined tube shown in figure if the pres-
sure at A is 7 kPa greater than that at
= 23.86°)
B. (Ans. 0 =
0.3 m
0.5 m
Oil
Water
3 m
Air
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Weighted piston type accumulator is shown in the figure below. If area=340 cm², a lift of the ram =1190 mm. Calculate the capacity of the accumulator in terms of liters.
Q 2/ Calculate the difference between PRESSURE OF COMPRESSED AIR at point A and PRESSURE OF CONFINED WATER at point B located in pipes shown in Figure bellow. (PA- PB). Water B 3 m Water Air 1.5 m Air 1.2 m
Q1:-The gate AB as shown in fig.1 has long 1 m and wide 0.9 m.Find the force F on The gate AB and also find the centre of pressure X 8 m 3 m 1 m Oil A 1 m S=0.81 7 m B 50 Fig.1
A tube of length L = 25.0 m that is open at one end contains airthe pressure of an atmosphere. It is pushed vertically into a freshwater lake.until the water rises halfway up the tube, see figure below. Suppose the temperature is the same at all points and does not vary with time. Adopt g=9.8 m/s2.a) What is the depth h of the bottom end of the tube?b) When was work W performed on the (ideal) gas inside the tube?
The cylinder shown in the figure extends 8 ft into the paper. If the cylinder has the radius of 4 ft, compute the vertical component of the hydrostatic force of the oil on the cylinder. 90 Oil (s.g. = 0.85 ) 4 ft 90° 50°
An infinitely long cylindrical container has a cross section area of radius R, and is placed horizontally with gravity being in the −y direction, as shown in the figure. The cylinder is 50% filled with water (the shaded part), with density ρ. The other 50% of the volume in the cylinder is filled with air with constant pressure of p = p0. The length of the cylindrical container in the axial direction is W. b) Use the surface integral method to compute the hydrostatic force acted on the 4th quadrant of the cylinder wall, as shown by the thickened line in the figure.
3.) The system in the figure below is at 20 °C. If the pressure at point A is 2900 lb/ft2, determine the pressures at points B, C, and D. Air Air 3ft 4ft Air 5ft 6t Water 2 ft
5. If the pressure difference between the two tanks in the figure shown is 20 kPa, calculate the value of a, in mm and angle 0, in degrees. The temperature is 20°C. Water A 26.8 cm 2a Mercury SG= 13.6 Water B
Q1: From Figure 1, the tube and the tank are open to the atmosphere. If L is 2.13 m, what is the angle of tilt 0 of the tube? Oil 50 cm Figure 1 SG = 0.8 Water 50 cm SG = 1.0
3.4 The tank shown in the figure is filled with a liquid and completely closed to be pressurized under a pressure Pair Determine the gage air pressure above the liquid A in bars. Take: l = 3.65 m, 12 = 1.25 m, 13 = 1.25 m, h = 1.15 m, hɔ = 0.85 m, Sg-A = 1.2, Sg-B = 1.0, Sg-c = 0.85, SHe = 13.6. Patm Reservoir, A Pair Liquid A 12 Mercury 3/4