A frame of two members (AC) and (BD) are connected together at pin B. The other ends are pin- supported at A and at D as shown in the figure below. A horizontal force of 500 N is applied on member (AC) at point C. The vertical component of reaction at pin A is: F= 500N 0.2 m 0.4 m 0.3 m Select one: O a. 250 [N] b. 500 [N] O c. 1000 [N] O d. 1500 [N]

A frame of two members (AC) and (BD) are connected together at pin B. The other ends are pin- supported at A and at D as shown in the figure below. A horizontal force of 500 N is applied on member (AC) at point C. The vertical component of reaction at pin A is: F= 500N 0.2 m 0.4 m 0.3 m Select one: O a. 250 [N] b. 500 [N] O c. 1000 [N] O d. 1500 [N]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show full work in handwritten format. Subject :Mechanical engineering Q:The flight path of a jet aircraft as it takes off is defined by the parametric equations x = 1.25 t2 and y = 0.03 t3, where t is the time after take-off, measured in seconds, and x and y are given in meters. If the plane starts to level off at t = 40 s, determine at this instant (a) the horizontal distance it is from the airport, (b) its altitude, and (c) its speed. Answer: 2000m,1920m and 175.3m/s respectively.
Show the mass of a flywheel needed to keep a machine’s speed within specified limits.
Please do this carefully.
Choose correct answer: When the cylinder is cushioned at the end of the stroke, how does cushioning affect the piston's force? At the beginning of the stroke, cushioning increases the piston's force. At the beginning of the stroke, cushioning reduces the piston's force. At the end of the stroke, cushioning increases the piston's force. At the end of the stroke, cushioning reduces the piston's force.
kinetics of particles-relative motion report
help! please write the complete solutions. Thumbs-up willl be given! DYNAMICS OF RIGID BODIES! A subway car leaves station A; it gains speed at the rate of 4ft /s2 for 6 s and then at the rate of 6ft /s2 until it has reached the speed of 48 ft/s. The car maintains the same speed until it approaches station B; brakes are then applied, giving the car a constant deceleration and bringing it to a stop in 6 s. The total running time from A to B is 40s. Determine the distance between stations A and B.
When a particle is subjected to both gravitational and elastic forces, the resultant force is expressed as which force?
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
help[
Part A U1 = Submit Each blade on a wind turbine is engineered to produce an effective force through its center of mass that is perpendicular to its long axis. (Figure 1) The magnitude of the force produced by each blade in a wind of speed v is F = (40.0 kg/s)v. If the center of mass of each blade is r = 10.2 m, what is U₁, the total work done by the wind turbine's blades, in a wind of speed v = 7.35 m/s after 10 revolutions? Express your answer numerically in joules to three significant figures. ► View Available Hint(s) Part B V ΑΣΦΗ n = Previous Answers Incorrect; Try Again – ΑΣΦ | 1 vec F vec Submit Previous Answers F A brake system is tested by rotating a tire and measuring the number of rotations required for the brake system to bring the tire to a stop. (Figure 2) The tire's radius is R = 50.0 cm and the brake system's radius is r= 19.3 cm. A moment of M = 13.8 Nm is applied to the tire for 5 rotations before the brake system is applied. The brake system is composed of two pads…
answer it in 20 mins. Determine the process. TOPIC: THERMODYNAMICS - PROCESSES OF GASES
The term "Slowly shifting dimension" should be defined and explained.