h₂ Water dB *** da huy=370lmag dA=200 [mm] dB = so[mm] no friction find Q hng

Q: Consider water transfer between two larger storage tanks. Lower tank water surface 10 m lower than…

A: Given data: Discharge (Q)=1m3s One storage tank is 10 m higher than the other. Let Z1 is the…

Q: Using the method of joints, determine the force in each member of the truss shown. State that member…

A:

Q: Determine whether the following equations are dimensionally homogeneous. pl t = mf represents an…

A: Given: The expression is t=plmf. l is acceleration, p is pressure, m is weight, t is time, f is…

Q: Compute the force matrix [Q],displacement matrix[D]and element axial force for the following truss…

A: Given: To find: Force matrix  Displacement matrix

Q: Data Table for Parts B – Resonance at 500 grams Measured String Density u measured = kg/m Length of…

A:

Q: 1) For beam shown below, find reaction forces in supports A & B 10[kN] 14.142[kN] 45° 4[kN/m] 0.2 А…

A:

Q: E₁ = 200GP₁₁ A₁ = 200 mm ² A 1.45 [m] 2 A = 400 mm ² C T point A and point D lies 2.625 m from wall…

A:

Q: Determine whether the following equations are dimensionally homogeneous. h = gt? h represents a…

A:

Q: 6[ft] в A с D E

A: To calculate the load at A, where the coefficient of friction , load at E is the distance

Q: Chiven Coupling V = 0.290). is 4340-HT Steel (E = 205 [C+Pa], G+ = 80 cpa, 6y = 470 GPa, 6₂ = 7195 ²…

A: Given: The Elastic modulus of the material used, E = 205 GPa The shear modulus of the material used,…

Q: If a student were performing this experiment at an ambient temperature and pressure of 70°F and 1…

A: Given-            temperature= 70 degree F           pressure= 1 atm            velocity = 15.5…

Q: Type BJ: A 5 kg block is pushed up along the slope as shown. The coefficient of kinetic friction is…

A:

Q: Determine whether the following equations are dimensionally homogeneous. 2ph3 f = mh 3t2 f is a…

A:

Q: Determine whether the following equations are dimensionally homogeneous. 2plh? gt 3m p is a force, l…

A:

Q: A pipe system takes water from a pool and circulates it through a filter using a pump. Answer the…

A:

Q: Ę TO n A x-axy F₁ M&F Yo Criven Q₁ = 15° 8₂=15° F₁ = F₁ = ± < 20, 5₁, -27 [N] r = 0.260 Find the…

A:

Q: 1.1 s) The overall size of the system (i.e. the shell) is 5.8 inch ID and a 27-inch long tube…

A:

Q: its throat, which can suck water from a deposit located under it. Assuming permanent flux with no…

A: Given data  D1= 15 mm D2= 37mm h= 163mm Pa= 101325kPa. find the velocity at throat (V1).

Q: A distributed load is applied to a beam with q1 = 4 [N/m] and q2 = 16 [N/m]. The geometry is given…

A: The free body diagram of the beam is shown below:Note: The pin support will give two reaction forces…

Q: In the cubic equation which is homogeneous, a · x° + b· x² + c · x + d = 0 x represents a length, a…

A: Write the given equation. ax3+bx2+cx+d=0 The given equation is homogenous. "a" is the weight…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.