What is the pitch diameter for an M24 fine-series threaded bolt? O 21.5 mm

Q: A frame of two members (AC) and (BD) are connected together at pin B. The other ends are pin-…

A: According to the information we have a frame with two members AC and BD that is pinned together at…

Q: Steel balls (diamęter = 21 mm, p= 7833 kg/m , k = 54 W/m-°C, Cp = 0.465 kJ/kg-°C, and a = 1.474x10 m…

A:

Q: What is the bird's spee

A: Given: Distance= 320m Time = 45 second Need To calculate the Speed

Q: A permanent bolted joint has four M24 ISO 8.8 bolts with coarse threads. The joint stiffness…

A: Answer: 136mm Solution is given below.

Q: A 10-ft' tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank is…

A:

Q: 16. K1 and K2 are springs in parallel. They are attached in series to spring K3, which is attached…

A:

Q: 2. A vertical square surface as shown in the figure as shown in the figure has its upper edge…

A:

Q: Question Both portions of the rod ABC are made of an aluminum for which E = 69.2GPA. Knowing that…

A:

Q: m /s, v=1.798E-5 m/s, Pr= 0.7228). If the optimum spacing is 12 mm, what is the heat transfer rate…

A:

Q: 1- In hybrid electric vehicle, the thermal engine operates at constant or variable speed. Justify.…

A: Given Hybrid vehicle Electronic control To find Thermal engine operation in hybrid vehicle…

Q: 2.3 x 10-13IM" 6.6 x 10 7 Jm PE(x) = Plot the potential energy curve as a function of separation…

A:

Q: An object of 40 kg mass falls freely under the influence of gravity from an elevation of 100 m above…

A: According to Work-energy theorem, the work done on a body is equal to change ins energy. This energy…

Q: P=4 t=14 Tall = 1.6 Strength of Materials HOME WORK1- Stress Member B is subjected to the…

A: P=4 t=14

Q: Prof. Dr. Necati Mahir esuzem Water -Boundary A piston-cylinder device initially contains 18 kg of…

A: Given Data m=18 kg P1=4 MPa T1=300°C W=2800 kJ P2=100 kPa

Q: Given data : Maximum principal stress=100 Mpa Minimum principal stress=-50 MPa Determine maximum…

A:

Q: 3. Determine the resultant force and specify where it acts on the beam measured from A. 9 kN/m 6…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: A brass boiler has a base area of 0-15 m2 and thickness 1-0 cm. It boils water at the rate of 6-0…

A:

Q: Fluid: Consider the following two tank system, where an input flow enters the first tank with…

A:

Q: A pressure-fed bearing has a journal diameter of 59.00 mm with a unilateral tolerance of -0.05 mm.…

A: Note: The given value of the journal diameter is incorrect. The journal diameter cannot be more than…

Q: find the initial velocity of a car which is stopped in 11 s by applying brakes. the retardation due…

A: Given data : The value of time=t=11 s The value of final velocity=V=0 m/s The value of…

Q: A cantilever beam has a spring constant k 80 N/m and an effective mass m = 7.68 x 10-1l kg. The…

A: Solution: Given Data:

Q: QUESTION 2 A vertical circular tank that is 1.5 m high, has sloping sides. The tank is 50 m and 30 m…

A:

Q: A gas turbine receives a mixture having the following molar analysis: 50% CO2, 10% H20, 40% N2 at…

A: Given Data: The temperature of mixture at the inlet is, T1=875 K. The pressure of mixture at the…

Q: Steam condensing at 120°C (h = 2203 kJ/kg) on the shell side of (1 shell and 12 thin- walled tubes)…

A:

Q: Hot fluid "C= 2562 J/kg.k , Pr=51.3, µ = 5.22E-3 Pa.s, k = 0.260 W/m.K" flows at 1.3 kg/min inside a…

A: Cp =2562 J/kg.K Pr = 51.3 Dynamic viscosity, u = 5.22*10-3 Pa.s k = 0.260 W/m.K Hot fluid mass flow…

Q: Question 1 An ideal-gas mixture consists of 2 kmol of N2 and 4 kmol of CO2. The gas constant (In…

A:

Q: fas The condenser of a steam power plant operates at a pressure of 7.38 kPa (Tsat = 40°C). Steam at…

A: SOLUTION  Saturated steam at a pressure of 7.38 kPa (Table A-9) condenses on a horizontal tube at 30…

Q: direction of motion 400 m The standing 400 m time of a car was 10.0s. Question 95 (2000 Question 1)…

A:

Q: Quickly

A:

Q: A circular plate of diameter (2.20 m) is placed some how 1.5 meter above the room floor, if the…

A: Given Data:- Diameter (d) = 2.20 m Raleigh number (Ra) = 7.653 × 107 × d3 Temperature (∆T) = 73°C…

Q: Consider the following cases: Case 1: A rod with specified surface temperature. Case 2: A rod with…

A: Given:

Q: Exercice 1: Déterminer, par la méthode des sections (de Ritter), la force dans la membrure EF due…

A:

Q: Consider an insulated pipe exposed to the atmosphere, then the critical radius of insulation:

A: Heat exchange rate will proportional to the outside fluid’s (velocity squared) and also the inside…

Q: The shear stress at the neutral axis in a beam of triangular section with a base of 40 mm and height…

A: Given data : Shear force =V V=3 KN Height=h h=20 mm Base=B B=40 mm   To find : Shear stress at…

Q: Draw the shear force and bending moment diagrams for the following beam. determine the Normal Force,…

A:

Q: Which of the following is true about robotics? a. Intelligent robots with artificial general…

A: All of the above options is true about robotics So option D is correct

Q: Develop a possible solution: (1) Draw a detailed diagram of a possible model Maglev train system,…

A:

Q: If the applied load "P" causes the point C to be displaced downward by Sc=1 mm, determine the normal…

A:

Q: The altimeter of an aircraft is set to the local pressure altitude of an airport. After takeoff the…

A: Find the condition of plane after change in pressure at an altitude = 2000m

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.