The kinetic data for the activity of 0.01mM enzyme is shown below. The concentration of {S} is millimolar and reaction rate is millimolar per second. Take this information down. Produce a Lineweaver-Burke graph using the data below, find the Km, find the Vm, and calculate the kcat for this enzyme. Turn in a single page with the graph (title, axes labels and units, etc) and the values of Km, Vm, and kcat (see the example image below)

The kinetic data for the activity of 0.01mM enzyme is shown below. The concentration of {S} is millimolar and reaction rate is millimolar per second. Take this information down. Produce a Lineweaver-Burke graph using the data below, find the Km, find the Vm, and calculate the kcat for this enzyme. Turn in a single page with the graph (title, axes labels and units, etc) and the values of Km, Vm, and kcat (see the example image below)

Biochemistry

9th Edition

ISBN:9781319114671

Author:Lubert Stryer, Jeremy M. Berg, John L. Tymoczko, Gregory J. Gatto Jr.

Publisher:Lubert Stryer, Jeremy M. Berg, John L. Tymoczko, Gregory J. Gatto Jr.

Chapter1: Biochemistry: An Evolving Science

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

You are working on an enzyme that obeys standard Michaelis-Menten kinetics. What variable is the V, dependant on if the concentration of the substrate is substantially higher than the concentration of the enzyme? [S] [E] [ES] O [P] O not enough information provided
Given the following information, calculate the catalytic efficiency of the enzyme. Step by step please [S] = 100 mM k1 = 10 sec-1 k2 = 3000 sec-1 k-1 = 20 sec-1 [E]T = 1 \muμM
You will perform the protocol below for the calf intestinal alkaline phosphatase (CIP) provided. For each reaction, your final enzyme concentration should be 10 nM CIP. Note: Enzymes purchased are typically labelled with their “units of activity” (U), as this relates to how much enzyme is needed to catalyze a reaction. The 100 nM CIP provided has approximately 3 U/mL and was diluted 1 in 1,000 from a 500 U/mL purchased enzyme. 1) Create a table (similar to the one below) to help you determine and keep track of what to add to each of the cuvettes in which your reactions will be measured. The five different concentrations of PNPP should be: 25, 50, 100, 200, 300 μM. Each reaction will be in a final volume of 1 mL and contain 10 nM alkaline phosphatase. Concentrations of stock solutions: 1.0 mM PNPP, 100 nM calf intestinal phosphatase
The Michaelis-Menten equation models the hyperbolic relationship between [S] and the initial reaction rate Vo for an enzyme-catalyzed, single-substrate reaction E + S ES → E + P. The model can be more readily understood when comparing three conditions: [S] > Km- Match each statement with the condition that it describes. Note that "rate" refers to initial velocity Vo where steady state conditions are assumed. [Etotal] refers to the total enzyme concentration and [Efree] refers to the concentration of free enzyme. [S] > Km Not true for any of these conditions Almost all active sites will [ES] is much lower than [Efree]. be filled. The rate is directly proportional to Increasing [Etotal] will increase [S]. Km: Adding more S will not increase [Efree] is equal to [ES]. the rate.
Draw a hypothetical Michaelis-Menten plot for an enzyme reaction (i) without and (ii) with a pure noncompetitive inhibitor. Label Vax and Km on plot
Please answer A & B attached with image.
An enzyme that follows Michaelis-Menten kinetics has a KM value of 3.00 µM and a keat value of 181 s1. At an initial enzyme concentration of 0.0100 µM, the initial reaction velocity was found to be 1.07 x 10-0 µM/s. What was the initial concentration of the substrate, S, used in the reaction ? Express your answer in micromolar to three significant figures. > View Available Hint(s) ? [S] !! µM Submit
Derive the rate law for the following enzyme reaction chain. Linear the equation you have derived as a Lineweaver-Burk type equation.
A graph of the Michaelis-Menten equation is a plot of a reaction's initial velocity (UO) at different substrate concentrations ([S]). First, move the line labeled Vmax to a position that represents the maximum velocity of the enzyme. Next, move the line labeled 1/2 Vmax to its correct position. Then, move the line labeled Km to its correct position. Estimate the values for V max and Km. 1/2 V max Michaelis-Menten curve 300 V max 275 250 225 200 v (μM/min) 175 150 K 2 125 m 100 75 50 25 0 0 10 20 20 50 58 30 40 50 60 60 [S] (μM) 70 10 60 80 90 100
An enzyme catalyzes a reaction with a K of 7.50 mM and a Vmax of 4.15 mMs. Calculate the reaction velocity, o, for each substrate concentration. [S] = 1.75 mM MM-s-1 [S] = 7.50 mM [S] = 11.0 mM DO mM-s mM-s
The Lineweaver-Burk plot, which illustrates the reciprocal of the reaction rate (1/v) versus the reciprocal of the substrate concentration (1/[S]), is a graphical representation of enzyme kinetics. This plot is typically used to determine the maximum rate, Vmax, and the Michaelis constant, Km, which can be gleaned from the intercepts and slope. Identify each intercept and the slope in terms of the constants Vmax and Km. What term is represented by C? Linewegver-Burk Pt 1/Vmax O A. В. -1/Km Km/Vmax C.
Explain why each of the following data sets from a Lineweaver–Burk plot are not individually ideal for determining KM for an enzymecatalyzed reaction that follows Michaelis–Menten kinetics.