The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear 1 and rotates at 1200 r.p.m. The gear wheels 2, 3, 4 and 5 are fixed to parallel shafts rotating together. The final gear 6 is fixed on the output shaft. F. Find: 1-the rotating speed of gear 6 2-rotating speed of gears (2, 3, 4, 5) The number of teeth on each gear are as given below:

The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear 1 and rotates at 1200 r.p.m. The gear wheels 2, 3, 4 and 5 are fixed to parallel shafts rotating together. The final gear 6 is fixed on the output shaft. F. Find: 1-the rotating speed of gear 6 2-rotating speed of gears (2, 3, 4, 5) The number of teeth on each gear are as given below:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An epicyclic gear shown in Figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.
The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of 982 rev/min. The tooth numbers are: N2= 18, N3= 45, N4= 12, N5= 34 Teeth respectively. Calculate the speed of output shaft 'c' in rev/min. Specify a positive number with 2 decimals
Q4: In an epicyclic gear train shown in the figure, the number of teeth of gear (A and S) are (200 and 98) respectively. If the gear (S) rotate with speed (450 r.p.m.) in C.W. direction and the gear (A) rotate with speed (100 r.p.m.) in C.C.W. direction, Determine the speed of the gear (P) and the arm (H). [Note: Start motion from gear (S)]. A Good Luck
Hey there! Calculate the IMA of the interlocking gears shown if the larger wheel (30 teeth) is turning the smaller wheel (24 teeth). Thanks! :)
Name: Referring to the given figure, spur gear A receives 5 hp at 650 rpm through its shaft and rotates clockwise. Gear B is an idler and gear C is the driven gear. The pressure angle o is 20° and the gear diameters: DA, DB, and DC are 6", 12", and 9" respectively. Determine: a. The torque each shaft must transmit, b. The tooth load for which each gear must be designed (Fr and Ft), C. The force applied to the idler shaft as a result of the gear tooth loads. C
Please use the following table and please the ratio is not 1.714 this answer is wrong. Please don’t reply with same answered way previously!!!!
I need answer in handwritten
plz solve 4 and 5 where X = 5
An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.
73 ll 6 O ... The pitch circle radius multiplied by the cosine of the pressure angle. Q3:- The increase of the contact ratio is desirable in gearing design because of:- * All of these The number of teeth will be increased in the engagement region More strength and more gear life will be achieved Smoother and faster motion None of these Q4:- To get best gearing design, it requires to:- * Increase sliding None of these Decrease sliding
lb pair of bevel gears having 20 and 75 teeth are used on axes that intersect at a 90" angle. Determine the velocity ratio and the pitch angles. of both gears.
For the gear train below, th numbers of teeth for individual gears are 12 9gear #1), Gear 18 (gear #2), 14 (gear #3), and 18(gear #4), To obtain a counter-clockwise rotation of 1500 rpm for the output gear(#4). What should be the rotation speed of the input gear (#1) and in which directions should the input gear rotate