Q2:- In an epicyclic gear train shown in the Fig. b, the internal wheels Aand F and the compound wheel C,D rotate about the axis O. Thewheels B and E rotate on pin fixed to the arm L. The wheels have thesame pitch and the numbers of teeth are: B and E 18, C 28 and D 26. Ifthe arm L makes 150 rpm clockwise, find the speed of F when (a) thewheel A is fixed; and (b) the wheel A makes 15 rpm counterclockwise.FD.

Answered: Image /qna-images/answer/6df2df0b-37f7-4e8e-9dce-1399c7fa8364.jpg

Answered: Q2:- In an epicyclic gear train shown…

Engineering

Mechanical Engineering

Q2:- In an epicyclic gear train shown in the Fig. b, the i and E and the compound wheel C.D rotate about the ax

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Two parallel shaft connected by spur gears turn in the same direction and having a speed ratio of SR…

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

Q: Q3:- The Fig. below shows an epicyclic gear train in which the gear D is held stationary by shaft A…

Q: (B) Two shafts A (driver) and B (driven) in the same straight line are geared together through an…

Q: in a planetary gear train, the arm C caries two gears A and B and a compound gear D-E. The gear A…

Q: The lath machine in the university mechanical workshop uses epicyclic gear train shown in Figure 1…

Q: A reverted gear train with a speed ratio of 12 consists of four gear wheels. Gear A has a module…

Q: In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is to be…

A: given pitch circle diameter of internally toothed ring dr = 220 mm module m= 4 mm the spider…

Q: Problem 2. 2000 rpm. Calculate the output The gear train shown below has an input speed nimput speed…

Q: nning at 100 rpm clockwise. B is an output shaft running at 250 rpm clockwise. Torque on A i

A: given:NA=100RPMNB=250RPMTA=50KN-m

Q: A gear system shown in Figure 1 consists of gear B and C with radii of 80 mm and 200 mm,…

Q: The bevel gear train shown is called Humpage's reduction gears. The input is to gear 2, and the…

A: The ratio of teeth on driven gears to the teeth on the driver gears for a gear train is termed as…

Q: In the coaxial gear train below, the speed of shaft Z is to be about but greater than 1/10th that of…

Q: The lath machine in the Central University of Technology (CUT) mechanical workshop uses epicyclic…

A: Given: The pitch circle diameter of gear D, dz = 214 mm The module of ring gear, m = 4 mm The number…

Q: 03/ The manually - operated hoist shown in figure (13) is based on an epicyclic gear train. The sun…

A: Given: The number of teeth on annulus, Za = 90 The tangential force on handle = 25 x load lifted

Q: A two-stage gear train consists of four gears meshed together (Figure 10). The secondand third gears…

A: for the given gear train To determine angular velocity of gear 4 in terms of ω1,n1,n2,n3 and n4

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

Q: A gear system consisting of a pinion and an internally toothed wheel is shown in Figure 3.1. The…

A: Given: The number of tooth on pinion, Zp = 21 The module, m = 5 mm The pressure angle, α = 20° The…

Q: A gear system shown in Figure 1 consists of gear B and C with radii of 80 mm and 200 mm,…

Q: For the epicyclic gear train shown, wheels B and C are rigidly attached to the input shaft (p) and…

Q: Question 1: Gears The lath machine in the Central University of Technology (CUT) mechanical…

Q: In the gear train shown gear 3 is carried on arm 5, Gear 3 meshes with gear 2 and gear 4. The number…

A: Here, Gear 2 is sun gear. Gear 3 is planet gear. Gear 4 is annular gear. Link 5 is arm. From the…

Q: An epicyclic gear train, as shown in Fig. 1, has a sun wheel S of 30 teeth and two planet wheels P-P…

Q: Question 1 A gear system shown in Figure 1 consists of gear B and C with radii of 80 mm and 200 mm,…

A: Given; The radius of gear B, rB = 80 mm The radius of gear C, rC = 200 mm The mass of gear B, mB =…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Q2:- In an epicyclic gear train shown in the Fig. b, the internal wheels A
and F and the compound wheel C,D rotate about the axis O. The
wheels B and E rotate on pin fixed to the arm L. The wheels have the
same pitch and the numbers of teeth are: B and E 18, C 28 and D 26. If
the arm L makes 150 rpm clockwise, find the speed of F when (a) the
wheel A is fixed; and (b) the wheel A makes 15 rpm counterclockwise.
F
D.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

6
Q: The sunwheel D has 20 teeth, the gear B is 50 teeth, internal gear C is fixed. The input shaft rotates at 2100 r.p.m. Determine the speed of the output shaft and the torque required to fix C when the gears are transmitting 30 kW. Output shaft Input shaft D
Three spur gear are arranged shown in the figure. Pinion A rotates for about 500 rpm. The three gears have a diametral pitch of 5. Number of teath and angle is shown in the figure. Determine the torque that each shaft is required to transmit and the resultant force on the shaft carrying the gear B. Draw the FBD of the figure.
Qestion-3: For the gear train shown identify which of the rack-gear will move faster (Gear-COR Gear-R) and how many modulos are powible? C and R: Rack Gears Dand B: Compound Gears R
2. The following data is for the gear train shown in the figure: Given: N2 = 30t, N3 = 35t, N4 = 55t, N5 = 40t, N6 = 50t, N7 = 40t %3D w2 = 30 rpm ccw, warm = 20 rpm cw, Input torque on gear 2 is 1200 lbf.in Determine the following: a. Angular velocity of the sun gear. b. The gear ratio R required to determine the angular velocity of gear 6. c. The angular velocity of gear 6. d. The angular velocity of gear 7. e. Output torque on gear 7. Be careful with your units. Arm 6 ... 7
5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft. Propeller Engine Reduction ratio 1.5 Engine is attached B
3. The center distance of two pair of meshing spur gears 4 = a, =160mm m, = m, z, = 20 3 = 30, 2, = 50 . Calculate the module of four gears and the tooth number of gear 1.
6. 5 3 Arm 6. 2 Arm Arm 2 3 1 Bearing Given N2 = 30, N3 = 25, N4 =45, N5 = 40, N6 = 200 W2 = 240 rpm ccw, warm = 120 rpm cw, T2 = 12 ft-lb Show your work. Answers without work will not be accepted a. Identify the gear sets. b. Determine the velocity gear train ratio and the angular velocity of gear 6. c. Determine the torque gear train ratio and output torque of gear 6.
In the pulley system shown in the figure, while the P gear rotates in the direction of 1 with its angular velocity, find the direction and angular velocity values of the other gears. Hint: The speed of the gears is equal at the point of contact. The speed of a belt is the same at all points.( w=3 rad/s , rk=0.8m ,rL=0.2 m ,rM=0.2m, rN=0.5m rP=0.4m rR=0.4m