(B) Two shafts A (driver) and B (driven) in the same straight line are geared together through an intermediate parallel shaft C as shown in the Fig. below. The gears connecting A and C have a module of 3 mm, those connecting C and B have a module of 6 mm. The speed of B is to be about (0.2) that of A. If the two pinions have 30 teeth, find the most suitable number of teeth for the gears, the actual velocity ratio and the corresponding center distance.

(B) Two shafts A (driver) and B (driven) in the same straight line are geared together through an intermediate parallel shaft C as shown in the Fig. below. The gears connecting A and C have a module of 3 mm, those connecting C and B have a module of 6 mm. The speed of B is to be about (0.2) that of A. If the two pinions have 30 teeth, find the most suitable number of teeth for the gears, the actual velocity ratio and the corresponding center distance.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: When you lift an object by moving only your forearm, the main lifting muscle in your arm is the…

A: Muscles, bones, and joints are some of the most interesting applications of staticsThe static…

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

Q: The reduction of speed from 360 r.p.m. to 120 r.p.m. is desired by the use of chain drive. The…

Q: (B) The sun and plant gear of an epicyclical shown in figure below the annular gear D has 100…

Q: The center distance between the two gear is 250mm and module is 5cm. Find the number of the teeth of…

A: module=diameter/teeth

Q: A gear train is composed of four helical gears with the three shaft axes in a single plane, as shown…

Q: degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of…

Q: Calculate the angle of twist at point A. A for the following diagrammed problem. There is a 1600…

A: The diameter of shaft AB is .The diameter of shaft CD is .The diameter of gear B is .The diameter of…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

Q: The lath machine in the ( mechanical workshop uses epicyclic gear train snuwn in Figure 1 to…

A: given data; ⇒pitch circle dialmeter (d) of gear D=214mm⇒module (m)=4mm⇒speed of arm(y)=1…

Q: The figure shows a schematic representation of a gear system. The gears are meshed with one another…

Q: Q4:- An epicyclic gear speed reduction is shown in the Fig. below. The driving shaft carries on the…

Q: A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: spur gear angle for the bevel gear at D is 18° and the bevel angle is 45°. Note that the shaft is…

A: Given : The radius is The pressure angle for the spur gear is The pressure angle of bevel gear at D…

Q: 8.10 Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in…

A: Given: Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed (N)=750rpm Power=4.6kW…

Q: consider a planetary train in the figure the number of teeth on gear sol (2) is Z2= 30, the number…

Q: Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Given :- Two spur gear of Z1=40 teeth and Z2=120 teeth Pinion rotates at N1=1200 rpm Torque is…

Q: The shaft from a DC motor is connected to gear A which rotates at 45rps in clockwise direction.…

Q: Gear 1 has a module of 4 mm/tooth and 25 teeth. This gear drives Gear 2 whose speed is 410 rpm. The…

A: The module of gear 1 is m1=4 mm/tooth. The number of teeth on gear 1 is T1=25. The speed of gear 2…

Q: The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and…

A: Gear: The gear is rotating part of the mechanical device. The gears are having the number of teeth…

Q: Please solve in 30 min The teeth number of each gear is already given (e.g. Z₁ =14). If the rotation…

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

Q: rpm of D in the clockwise direction is

A: Figure shows the epicyclic gear train.For this data is given as: Number of teeth on the gears;…

Q: 1. Classification of gears according to the possibility of movement of gears axis of rotation…

A: Introduction: A gear is a spinning circular machine element with cut teeth or inserted teeth that…

Q: Q2:- In an epicyclic gear train shown in the Fig. b, the i and E and the compound wheel C.D rotate…

Q: nism when annulus is i

A: introduction: we have to find out degree of freedom

Q: 4. For the extended epicyclic gear train shown. Gears 1, 3, and 6 have internal teeth while gears 2,…

A: In gear train , we knowvelocity ration=velocity of first drivervelocity of last driverBy using…

Q: Q(1): For the component epicyclic gear train shown in the figure, the number of teeth of gears (A, B…

A: Given diagram:

Q: Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4…

Q: Two internal 10-pitch, 20° full-depth gears are used in a system. The pinion has 28 teeth and the…

A: Given Data The number of teeth on pinion is:t1=28 The number of teeth on the gear is:t2=70 The…

Q: Each of two gears in a mesh has 60 teeth and a module of 6 mm. The teeth are of involute profile.…

A: Data given- T = 60 m = 6 mm Arc of contact = 2.5 × circular pitch

Q: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

A: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

Q: Q4: In an epicyclic gear train shown in the figure, the number of teeth of gear (A and S) are (200…

A: For the given epicyclic gear train let C.W. direction be positive and C.C.W. direction be negative.…

Q: Shaft a in the figure has a power input of 75 51T kW at a speed of 1000 rev/min in the…

A: Given data Input power = 75 kW Input Speed = 1000 rpm module = 5 mm Number of teeth on gear 1 = z1 =…

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

Q: An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring…

Q: An epicyclic gear consists of ring gear, planet gear and sun gear. The ring has 72 internal teeth…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

(B) Two shafts A (driver) and B (driven) in the same straight line are geared
together through an intermediate parallel shaft C as shown in the Fig. below. The
gears connecting A and C have a module of 3 mm, those connecting C and B have a
module of 6 mm. The speed of B is to be about (0.2) that of A. If the two pinions
have 30 teeth, find the most suitable number of teeth for the gears, the actual
velocity ratio and the corresponding center distance.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

please help solve
lb pair of bevel gears having 20 and 75 teeth are used on axes that intersect at a 90" angle. Determine the velocity ratio and the pitch angles. of both gears.
The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating at a speed of 1200 revolutions per minute. It must increase the torque received at its input shaft 16 times. Spur gears with 20° pressure angle should be used. Input and output shafts should be aligned. The transmission should take up as little space as possible. The distance between the centers of the input shaft and the intermediate shaft (the one that loads gears 3 and 4) should be 10 inches. Determine the magnitude of the radial load that gear 4 exerts on gear 4. Write your answer in pounds.
In a spur gear arrangement, the driver has 80 teeth of 39 mm pitch. Find the power, if it can transmit a tangential force of 60 N. Take speed of driver as 150 rev/min. Insert your answer for power in watt correct up to at least a third decimal place.
i need the answer quickly
Q: The sunwheel D has 20 teeth, the gear B is 50 teeth, internal gear C is fixed. The input shaft rotates at 2100 r.p.m. Determine the speed of the output shaft and the torque required to fix C when the gears are transmitting 30 kW. Output shaft Input shaft D
Three spur gear are arranged shown in the figure. Pinion A rotates for about 500 rpm. The three gears have a diametral pitch of 5. Number of teath and angle is shown in the figure. Determine the torque that each shaft is required to transmit and the resultant force on the shaft carrying the gear B. Draw the FBD of the figure.
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts is 600 mm. If one shaft runs at 120 r.p.m. and the other at 360 r.p.m., find the number of teeth on each wheel, if the module is 8 mm. Also determine the exact distance apart of the shafts.
In a spur gear arrangement, the driver has 70 teeth of 26 mm pitch. Find the power, if it can transmit a tangential force of 100 N. Take speed of driver as 160 rev/min. Insert your answer for power in watt correct up to at least a third decimal place.
A recurring gear train composed of four sprockets 2, 3, 4, 5, has a value of the train of 1: 4 ½, being all the teeth of the gears of the same pitch. 2 has 40 teeth, 3 has 60 teeth. Find the number of teeth in 4 and 5. If the diametral pitch is 3, find the distance between the centers of the arrows. Answer N4 = 25; N5 = 75; 16.667 in
An epicyclic gear train is shown in the figure. The number of de grees of freedom possible for this mechanism when annulus is fixcd arc