The drive belt of the lathe machine is noticed with excessive wear, maintenance step followed is Replaced with same matched set of drive belts  Repair the drive belts found with excessive wear Replaced with different matched sets of drive belts  No need to repair the drive belt with excessive wear

Q: Road test Report is Overhaul all four-wheel brakes and the Universal joints After the maintenance…

A: Option - B , D  => After operation is completed the road test report will happen to check the…

Q: What conditions does Compatibility specify?

A: In the field of mechanics, compatibility means when there is continuous deformation (displacement of…

Q: How important is to follow the scheduled maintenance for the propeller like for overhaul inspection,…

A: overhaul inspection and annual inspection of the propeller

Q: mention five Machine tools used in workshops and explanation of the various parameters in Condition…

A: Machine tools used in workshops

Q: What is Brake horsepower and where did the name come from?

A: Brake horsepower (bhp) is a term used to describe the power output of an engine or motor. It is…

Q: In an automatic AWD vehicle, normally one axle receives all the torque; when slippage occurs, 50…

A: In an AWD vehicle, when one axle receives all the torque, the torque can be sent to the other wheels…

Q: Which of the following statements about drum brakeshoes is not true?a. Web thickness varies only…

A: Brake shoes are a major part of a drum brake system. these crescent-shaped components are made up of…

Q: Technician A says that some small cracks in the accessory drive belt may be within tolerance.…

A: Technician A says that some small crack in the accessory drive belt may be within tolerance limits.…

Q: of Disc check va

A: Stage 1 given; What the destroying and Assemble of stomach valve Also what is capacity of part than…

Q: Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the…

A: A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward…

Q: Technician A tests brake drums for out-of-round using a dial indicator. Technician B measures the…

A: The break is the device which are used to deaccelerate the moving objects. It is based on the…

Q: By monitoring the condition of the machine, preventive maintenance can not be performed to increase…

A: In preventive maintenance- Equipment downtime is decreased and the number of major repairs is also…

Q: In _vibrations, the amplitude of vibration reduces over every cycle of vibration. O forced O free…

A: In _________vibrations, the amplitude of vibration reduces over every cycle of vibration. O forced O…

Q: Discbrake friction linings are sometimes called brake The ratio of the force required to slide one…

A: Given questions are related to IC engines and Machine design             [Note : According to…

Q: It is common practice to assign a larger portion of the location tolerance to the hole.

A: Fill in the blanks.

Q: Technician A says it's important to preload the plunger on a dial indicator before attempting to…

A: Technician A says it's important to preload the plunger on a dial indicator before attempting to…

Q: A

A: Given : The tolerance off hole = 0.5

Q: Unilateral Tolerance is Total tolerance is in both the directions May or may not be in any direction…

A: Unilateral tolerance is the type of tolerance in which true profile is only permitted in one…

Q: What type of bearing is recommended for a dirty environment?

A:

Q: Determine the internal forces acting in members, HC, JD, and KE. State if the members are in tension…

A: Drawing the free body diagram of the system as shown below,…

Q: What’s is the purpose of breaking in new disc pads

A:

Q: among the ruler and vernier caliper gave the least % err

A: Ruler and vernier caliper both are measuring devices.

Q: how to position this locator on a plate base for a part to ensure conformance with the Production…

A:

Q: 67. Which of these angles is adjusted last during a wheel alignment? a. Steering axis inclination c.…

A: " Since you have asked multiple questions we will solve the first question for you. If you want any…

Q: When removing the balance shaft assembly: tech a inspects the bearings for unusual wear or damage.…

A: Balance shafts are serviced in the same way as crankshafts.there are two main causes of removing or…

Q: 1. A toe adjustment of 1/8 inch outside of specifications will have little effect on tire life. a.…

A: Hii, thanks for the question but we are authorized to answer three parts at a time. Here you did not…

Q: 108) Technician A says that engine management malfunctions may be misinterpreted as transmission…

A: Engine management malfunctions can be seen by malfunction indicator lamp . this indicator shows that…

Q: The typical RWD drive shaft rotates how many times faster than wheels

A: The typical Rear Wheel Drive (RWD) shaft  rotates three times faster than the wheels,

Q: how to postion this locators and ensure conformance with the Production Part tolerances using the…

A: Given Data:   To Find: How to position the 3 given locators.

Q: 109) A customer complains that his vehicle will not move when first shifted into gear. Technician A…

A: When the vehicle sit engine off over night, fluid from the torque converter drains back . It drain…

Q: Tighten the cylinder head nut in the order prescribed by----- -----, using the appropriate torque by…

A:

Q: After draining gear oil from a transaxle, the techniciannotices that the oil has shiny, metallic…

A: For a transmission or axle to last longer, it needs to be properly lubricated. After the required…

Q: ___________ tool is used for verifying the flatness of the component.     A. Protractor…

A: Protractor is a device used to measure the angles. Engineers square is a checking tool which is used…

Q: Q 2/True or false 1- Casing pipe is used to rotate the bit and circulate the drilling fluid. 2- On…

A:

Q: structural analysis and assembly of gearbox

A: Structural Analysis of gearbox   Nature of loading within the various components of a gear box is an…

Q: The radial distance of a tooth from the pitch circle to the top of the tooth is called O Module O…

A: Module: Module  is the unit of size that indicates how big or small a gear is. Clearance: Clearance…

Q: Replacing the tyre after it burst is example of breakdown maintenance. an Select one: O True O False

A: Breakdown maintenance is an unplanned maintenance which will occur when we are in the situation to…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.