The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (b)allow 2 ksi, and the allowable tensile stress within the bolt shank S is (allow 18 ksi, determine the maximum = allowable tension in the bolt shank. The bolt shank has a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.

Q: If load P = 20.1 kips, determine the normal force in bar (1). A 6 ft 46.6 kips 39.5 kips 33.5 kips…

A:

Q: Find the young modulus of the rod of diameter 50 mm and of length 400 mm which is subjected to…

A: Given data:

Q: Situation 1: A flexible cable and rigid boom system is used to lift a load of 65kN at the end of…

A:

Q: Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing…

A: TRUSS:- is a rigid structure in which all he members are subjected to either axial or  tensile or…

Q: A-2 Determine the vertical displacement of joint C.Assume e members are pin connected at their end…

A: A = 200 mm²   E = 200 Gpa

Q: A detailed view is shown for the connection Bin the concrete trough. The tension in cable B is 450…

A:

Q: Q2/ Determine the maximum allowable load P that can be safely suppom 1.5 in. and b-4 in. The wood…

A: t=1.5inb=4inσfail=2ksiζfail=2ksiFOS=1.5   To-Find:- P=?

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given data d=0.75 inP=52 kipsn=5 Here, d is the diameter and P is the load applied.  Here, n is the…

Q: find the bearing stress between bolts and plate 10/-.. 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN…

A: Given data  diameter of bolt (d) = 10 mm thickness of plate (t) = 8 mm  Load acting on the plate…

Q: A rod has a solid circular cross section with a diameter of 40 mm is subjected to the shown loads.…

A: To find: The state of stress at point A. Given: The area moment of inertia of solid circular cross…

Q: et's consider a rod having a solid circular cross-section with diameter of 4 mm and it i5 made of a…

A: given:diamater d=4mmyoung modulus E=200GPapoisson ratio μ=0.3

Q: Bar (1) has a cross-sectional area of 0.75 in.?. If the stress in bar (1) must be limited to 35 ksi,…

A:

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: For aluminum rod,For steel rod,The displacement towards A  to left is,

Q: A 10 mm 10 m Pin B Bracket 6 mm S m

A: GIVEN: The weight of bar = 3000 kg limited shear stress = 60 MPa

Q: determine

A: For factor of safety at B we have to determine effective stress at B σ=σy2+3τxy2+τyz2 σy(Axial…

Q: n the steel structure shown in the figure, a 6 mm diameter in is used at C and 10 mm diameter pins…

A:

Q: An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If…

A:

Q: ny mm is the smallest allowable outer diameter of the washer

A: GIVEN :- Diameter of rod : d= 34mm washer inner diameter : di  = 37.5 Allowable stress of rod : σ=…

Q: Q31 A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside…

A:

Q: For the Problem-1, determine the critical load if its length is 700 mm

A: The length isDiameter of the barYoungs modulus

Q: A force P of magnitude 950 N is applied to the pedal shown. NOTE: This is a multi-part question.…

A: The value of force P is 950 N The thickness of the support is t=5 mm

Q: The boom is supported by the winch cable that has an allowable normal stress of allow = 24 ksi. It…

A:

Q: The axial load 274 kN applied to the lap joint is distributed equally among the three…

A: Given:  P = 274 kN n = 3 d = 26.5 mm  w = 135.4 mm  t = 29.5 mm

Q: arked a---a. Just at this si

A: given:

Q: e wrenches to ensure that a bolt has a prescribed on when used for connections. If a nut on the bolt…

A:

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given: Let us consider the given data,  d=0.75P=56 kipsn=5 Where, d=Diameter P=Applied load n=Bolt…

Q: 3 Determine the maximum safe : load P can be applied. P. if the shearing stress P in the rivets is…

A:

Q: width of the plates and pin if the load applied is 45 KN. The allowable tensile 180MPA and the…

A: Find the width of the pin by using the below expression. Now substitute the required value in the…

Q: A link in a mechanism is made from round bar. Due to the loading condition, the link is subject to a…

A: Maximum stress is 68 MPa Minimum stress is -27 MPa Required: Alternating stress

Q: find the tensile of the bolt with diameter 38mm,80kN

A:

Q: sectional area of Arod = 0.75 in². If a load of P = 24 kip is applied to the end of rod, determine…

A:

Q: A 2" diameter pin connects the three links as shown. The links have a 3" by 3" cross- section.…

A:

Q: Determine the reaction loads and maximum shear stress ! 200 Ibf-in z-in dia. A B 4 in 6 in

A:

Q: Determine the maximum safe load P that can be applied to the machine part that is 90-mm wide and…

A: GivenW=90mmt=12mmσallow=100Mpa

Q: The five-bolt connection must support an applied load of P = 4300 lb. If the average shear stress in…

A:

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: For aluminum rod,For steel rod,The displacement towards A  to left is,

Q: The five-bolt connection shown must support an applied load of P-500 kN. If the average shear stress…

A:

Q: Determine the magnitude of the pin force at A. Assume W-515 lb, a -4.7 ft, b-3.8 ft, r - 8 in. W C…

A: To find: The magnitude of the pin force at A. Given: The weight is W=515 lb. The lengths are a=4.7…

Q: The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and…

A:

Q: The homogeneous bar AB weighing 2000 lb. is supported at either end by a steel cable. Calculate the…

A: