A-2 Determine the vertical displacement of joint C.Assume e members are pin connected at their end points. Take = 200 mm² and E = 200 G Pa for each member. Use the ethod of virtual work. 4m 3m 12 kN B S 3m

Q: State three uses of the combination set

A: Combination set is an measuring tool, it is used to measure angles and lengths.

Q: 1. T-square is used for drawing: A. horizontal lines b. inclined lines c. vertical lines d. lines at…

A: We have to find term 1,2,3

Q: Find the value of a. TO a. Vs +3

A:

Q: solve and show every step with right answer

A: Data given - Rectangular cross section 225×75 mm2 Torsional moment = 20kN Axial Compressive force =…

Q: 355 coupe for some maintenance check. Before proceeding to your regular maintenance routine, it is…

A: Odd matric number:

Q: Convert the decimal number 35710 into its octal number equivalen

A: Steps Write the given decimal number. If the given decimal number is less than 8 the octal number…

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: draw the left side

A:

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: 2 Constraint indicated the name and where it should be

A: Given: To find: Where the constraint should be

Q: a) What is the reading (degrees, minutes)? b) What is the reading (degree and fractions of a…

A: Reading on main scale = 90 degreeReading of vernier matching with main scale = 22Least count of…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: Match the letter to the correct part description based on the picture of the milling machine below.

A: Milling Machine Parts name

Q: L t C Determine the moments at fixed ends 'a' and 'd' ?

A:

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: Find the angle e for the given figure 800 N y 8 3 O a. 63 О ь. 59 с. 69 O d. 66

A: From the given figure...

Q: A 2.10kg pole is attached to a wall with a hinge as shown. A 5.80kg sign is suspended at the other…

A: Given data: mp=2.10 kgM=5.8 kgD1=1.3 mD2=3.2 mα=19.0° Need to determine the torque on the pole due…

Q: A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. With two 3.17 g coins…

A:

Q: 1500# 1500# 1500# 1500# 12' K I

A: In this problem, following steps will be taken 1. Determine the reactions at the supports.' 2. Using…

Q: Write the types of keys and sketch freehand of them with dimensions and equations.

A: A key is a machine element that is fitted in the axial direction with the mating parts in pulleys…

Q: In a lathe machine tool, when the cutting tool moves parallel to the axis of rotation of the…

A: It is required to justify given statement

Q: 200 m The spool has a mass of 40 kg and a radius of gyration of k-0.65 m. If the 20 kg weight is…

A:

Q: 1. How is fraction changed to decimal? A. Divide the denominator by the numerator B. Divide the…

A: Since we answer only one question at a time, we will answer the first one. Please resubmit the…

Q: N

A: Given: To find: Correct rotation code

Q: For the laser cutting of the shown path, determine the absolute and incremental coordinates of the…

A: given; findabsolute and incremental co-ordinate;

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.