The concrete post (Ec = 30 GPa and =10x10 /C) is reinforced with six steel bars, each of 10 mm diameter (Es = 210 do %3D -6 o %3D -6 o GPa and a = 12x10 / C). Determine the normal stress-induced in the steel by a temperature fall of 70 °C.

The concrete post (Ec = 30 GPa and =10x10 /C) is reinforced with six steel bars, each of 10 mm diameter (Es = 210 do %3D -6 o %3D -6 o GPa and a = 12x10 / C). Determine the normal stress-induced in the steel by a temperature fall of 70 °C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of 200 mm, a wall thickness of 5 mm, and a length of 5.4 m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 6= i AD= i mm mm
Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow)con = 2.4 ksi and (allow)st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 × 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 10 ft 9 in. H 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. Pmax = Submit 04 μA Provide Feedback Value Request Answer Units ?
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
Situation 5: The compound bar, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25°C. Assume that the walls do not yield and use the following data: A (mm²) a (/*C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segrnent 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10- 200 - 500 mm→- 400 mm- 800 mm Aluminum Steel Bronze 17. Compute the stress in the bronze bar a. 31.6 MPa (T) b. 31.6 MPа (С) 18. Compute the stress in the aluminum bar. а. 45.1 MPа (Т) b. 45.1 MPa (C) 19. Compute the stress in the steel bar. 79.0MPA (T) 79.0MPA (C) 13.6 MPa (T) 13.6 MPa (C) c. d. 54.1 MPа (Т) 54.1 MPa (C) с. d. a. C. 97.0 MPa (T) b. d. 97.0 MPa (C)
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ? P steel raid steel sF I A=0-1 Mat 50°d E = 200 GPa -Aluminum L= 250 Mm A = 1600 mm ² X = 12 x10%2 Call = 200 MPa Comp Alumivun Post. E = 73 GPa A = 2400 mM 400 mM 40o mm 2 X = 23 x 10% T = 150 MP Comp Figure 2
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 15 mm, and a length of 5.5 m. The pipe supports a compressive load of 635 kN. After the temperature of the pipe drops 45°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 3.6 kips/ft, LAB = 5.6 ft, LBC = 5.6 ft, and LcD = 16.8 ft. Determine the magnitude of the maximum bending stress in the beam. LAB Answer: Omax = i B LBC C ksi W LCD D ZOQ Q 214% TOP BARI ENG 11:41 am 35 28/04/2023 8 cores
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
3. Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load P=75 KN is applied. Neglect the deformation and mass of the horizontal bar AB. Use Ea = 75 GPa, as=23.0 um/m-°C, Aa = 850 mm2 Es = 210 GPa, as = 11.9 um/m-°C and As = 650 mm² . %3D %3D Steel Aluminum 3m 2.5m 3 m 3 m 3 m 75 KN
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of 225 mm, a wall thickness of 15 mm, and a length of 5.0m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 48°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = mm AD= i mm