The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm. Determine the stress in the concrete and the steel if the post is subjected to an axial load of 900 KN. Assume that E = 200 GPa for steel, and E= 25 GPa for concrete 900 KN 250 mm 375 mm stress in steel = 65.3 MPa and stress in concrete = 6.4 MPa stress in steel = 67.3 MPa and stress in concrete = 8.4 MPa

The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm. Determine the stress in the concrete and the steel if the post is subjected to an axial load of 900 KN. Assume that E = 200 GPa for steel, and E= 25 GPa for concrete 900 KN 250 mm 375 mm stress in steel = 65.3 MPa and stress in concrete = 6.4 MPa stress in steel = 67.3 MPa and stress in concrete = 8.4 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
Question 2. The concrete column (30 x30) cm, length 6 m, Ec = 4 x 106 MN/m² and ac = 5.5 x 10/ "C is reinforced with eight steel bars, each of 12 mm diameter (Es= 29 x 106 MN/m² and as = 6.5 x 10"/ "C). Determine the normal stresses induced in the steel and in the concrete by a temperature rise of 75 °C.
Assuming concrete is uncracked. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1x10°kg cm . Determine the cracking moment of the section. A = 10cm² %3D E, = 2*10°kg / cm² E = 2*10°kg / cm² %3D %3D f'. =1836kg / cm² %3D 90 cm 100 cm 40 cm
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
Three high-strength concrete poles, with an effective cross- sectional area of 40, 000m * m ^ 2 and a length of 2 m, support a stiff steel plate. The center post is 1 mm shorter than the others before the load P is applied. If the concrete's allowed compressive stress is 20 MPa, calculate the maximum load that can be carried. E = 30GPa for concrete
Situation no. 1: Calculate the bending stresses in the concrete and the reinforcing steel, using the transformed area method: fc= 3000 psi, normal- weight concrete, n= 9, M = 250 ft-k. %3D -bym 60 in. - 1. Bending stress of concrete. a 0.057psi My = 5 in. b. 57ksi 不 A,=6 hars C. 6840 ksi d= 28 in. 684psi e. 2. Bending stress of steel. a. 24 4ksi b. 2.03 ksi C. 24354.00ksi 2.71ksi b12 in. d. e.
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 400 mm. Concrete strength is f’c = 28 MPa and steel yield strength is fy = 280 MPa. a. What is the distance of the neutral axis from the top of the beam so that the strain in the concrete 0.003 will be attained at the same time with the yield strain of steel? b. What is the total compressive force on concrete? c. What is the balanced steel ratio?
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
PROBLEM TO SOLVE: 600 mm 400 mm Using fe' = 28 MPa, Mmax = +320 kNm Determine the following: a. Cracking Moment (kNm) 6-25mm diam. b. Compressive Stress felt by concrete (MPa) c. Tension Stress felt by the tension bars (MPa)
Given the following properties of a rectangular concrete beam: b = 300mm, d = 425mm, f'c = 28 MPa, fy = 415 MPa. The beam is reinforced for tension only. when the beam is reinforced with four 25mm diameter bars. Determine the steel ratio. (A) 0.0143 (B) 0.0169 c) 0.0154 D) 0.0186
The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation . Ust Bearing |1000 kN plate Steel- Concrete 300 mm 300 mm Section a-a