Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.

Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve only part 1 also draw free body diagram
A Normal-weight concrete T beam shown in the figure below is reinforced at the tension side by 3 - #25 bars. The concrete is assumingly uncracked and has a compressive strength of fe' = 29 MPa, fy=370 MPa, and the clear concrete cover is 40 mm, the modular ratio is n=9, and the web rein. is #10 mm. Determine the cracking moment (kN m) of the section using solution 2. 1300 125 250 500
Determine the maximum concrete and steel stresses at the point of maximum positive and negative moments. Reinforced Concrete Design
In a reinforced concrete section, the stress at the extreme fibre is compression is 5.80 MPa. The depth of neutral axis in the section is 58 mm and the grade of concrete is M25. Assuming linear elastic behavior of the concrete, the effective curvature of the section (in per mm) is
/ For the rectangular reinforced concrete beam (shown below),determine the stress at the upper and lower fibers of concrete and at steel reinforcement if fc'=20 MPa
Please try to solve only part 2 within 20 minute This is request
In all Questions use the Working Stress Method and the flowing material 25 MPa and f, = 420 MPa. properties f = If the stress in the top fiber of the concrete is f = 12.5MPa and in the steel is 400 MPa. Ec 25000 MPa, Es 200000 MPa. Determine the following: 1-Maximum strain in concrete 2- Maximum strain in steel and 3- Flexural strength of the section (the moment M) P 500 mm 300 mm
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f'c = 21 MPa and steel yield strength fy = 420 MPa a.) if the tensile strain is es = fy/Es upon crushing of concrete at a strain of 0.003 b.) if the tensioe strain is set as 0.009 upon crushing of concrete at strain of 0.003 c.) minimum as required by NSCP 2015
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It is reinforced with 4-36 mm diameter bars at the tension side of the beam placed 75 mm above the bottom of the beam. f = 25 MPa, fy = 414 MPa, E, = 200,000 MPa. Which of the following is the nominal moment capacity of the beam.