The composite shaft shown consists of a 0.15-in.-thick brass jacket (G= 6 x 106 psi) bonded to a 1.4-in.-diameter steel core (Gsteel 14 x 106 psi). The shaft is subjected to 8.5-kip-in. torques.as shown, detremine (a) the maximum shear stress in the brass jacket and (b) angle of twist of B relative to A 6 ft Steel core Brass jacket

The composite shaft shown consists of a 0.15-in.-thick brass jacket (G= 6 x 106 psi) bonded to a 1.4-in.-diameter steel core (Gsteel 14 x 106 psi). The shaft is subjected to 8.5-kip-in. torques.as shown, detremine (a) the maximum shear stress in the brass jacket and (b) angle of twist of B relative to A 6 ft Steel core Brass jacket

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4-37 The composite bar consists of a 20-mm-diameter A- 36 steel segment AB and 50-mm-diameter red brass C83400 end segments DA and CB. Determine the average normal stress in each segment due to the applied load. 4-38 The composite bar consists of a 20-mm-diameter A- 36 steel segment AB and 50-mm-diameter red brass C83400 end segments DA and CB. Determine the displacement of A with respect to B due to the applied load. -250 mm- 50 mm DA - 500 mm 20 mm 75 KN A 75 kN 100 KN -250 mm- 100 KN B C
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
4. Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at both ends through the fiberglass as shown. The diameter of the bent bar is 1/4" Ø, outside diameter of the washer is 7/8" Ø and the thickness of the fiber glass is 3/8". The working shear stress between the fiberglass and the washer is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi. Use 2 decimal places in every solved value. bent bar fiberglass washer bolt cap 7 8. 8 1/14
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ? P steel raid steel sF I A=0-1 Mat 50°d E = 200 GPa -Aluminum L= 250 Mm A = 1600 mm ² X = 12 x10%2 Call = 200 MPa Comp Alumivun Post. E = 73 GPa A = 2400 mM 400 mM 40o mm 2 X = 23 x 10% T = 150 MP Comp Figure 2
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
A stepped shaft has the appearance shown in Fig 5-13. The region AB is aluminum, having G= 28 GPa, and the region BC Is steel, having G- 84 GPa. The aluminum portion is of solid circular cross section 45 mm in diameter, and the steel region is circular with 60 mm outside diameter and 30-mm inside diameter Determne the maximum shearing stress in the aluminium in MPa if a torsional load ot 4000 N m is applied at B. Ends A and Carerigidly damped. 45 mm 60 mm 30 mm 12m
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
A steel latch is 6 mm thick. A force F of 3000 N is uniformly distributed as shown below. Do not consider the stress concentration! a) Determine the principal stresses at Scction B-B?. b) Determine the principal stresses at point A? 3 kN Y R30 L, A 125 09
A rectangular steel block is 3.2 inches long in the x-direction, 2.9 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 48 kips tension in the x-direction, 65 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
The beam shown left below has the cross section shown right below. Determine(a)The maximum tensile fiber stress in the beam.(b)The maximum compressive fiber stress in the beam.(c)The shearing stress 50 mm below the top surface of the flange.(d) The maximum shearing stress
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i