The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment (1) is a tube with an outside diameter of D₁ = 4.15 in., a wall thickness of t₁ = 0.25 in., and a shear modulus of G₁ = 4,000 ksi. Steel segment (2) is a tube with an outside diameter of D₂ = 2.00 in., a wall thickness of t₂ = 0.125 in., and a shear modulus of G₂ = 12,000 ksi. The compound shaft is subjected to torques applied at B and C as shown. Determine the rotation angle of C with respect to the support at A. (1) 9 ft -0.0343 rad -0.0429 rad -0.0259 rad -0.0320 rad O-0.0460 rad 1,700 lb-ft B (2) 6 ft 650 lb-ft C X

The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment (1) is a tube with an outside diameter of D₁ = 4.15 in., a wall thickness of t₁ = 0.25 in., and a shear modulus of G₁ = 4,000 ksi. Steel segment (2) is a tube with an outside diameter of D₂ = 2.00 in., a wall thickness of t₂ = 0.125 in., and a shear modulus of G₂ = 12,000 ksi. The compound shaft is subjected to torques applied at B and C as shown. Determine the rotation angle of C with respect to the support at A. (1) 9 ft -0.0343 rad -0.0429 rad -0.0259 rad -0.0320 rad O-0.0460 rad 1,700 lb-ft B (2) 6 ft 650 lb-ft C X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional dimensions of the beam are b1 = 32 mm, d1 = 117 mm, b2 = 19 mm, d2 = 19 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 13 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M | A В
Problem # 2. At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 140 °C, determine (a) the normal stress in the aluminum rod Ans: A -300 mm Aluminum A = 2000 mm² E = 75 GPa α = 23 x 16-6/°C 0.5 mm -250 mm Stainless steel A = 800 mm² B E = 190 GPa a = 17.3 x 10-6/°C
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 93 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 9 MPa. Determine the %3D largest moment M that can be applied as shown to the beam. b2 M d2 d1 | A B L b1 Answer: M = i N•m
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000 ksi; a = 6.5x10-6/°F] bolts have a diameter of 0.30 in. The polymer [E = 370 ksi; a = 38.3x 10-6/°F] cylinder has an outside diameter of 6.6 in. and a wall thickness of 0.75 in. Assume a = 29 in. and b = 37 in. If the temperature of this assembly changes by AT = 135°F, determine: (a) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) the normal strain in the steel bolts. %3D %3D %3D %3D (1) C (2) a (1) b. Answer: (a) 02 = psi. (b) E2 = 3d (c) E1 =
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm. The cross-sectional dimensions of the beam are b, = 36 mm, d1 = 95 mm, b2 = 22 mm, d2 = 22 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 M d2 d1 |A В b1 Answer: M = N-m
At room temperature (20°C) a 0.7-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 150°C, determine: (a.)The normal stress in the aluminum rod, (b.) The change in length of the aluminum rod. 0.7 mm 300 mm A Aluminum A =2,000 mm² E= 75 GPa α = 23 x 106/°C 250 mm B Stainless steel A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C
Engineering Mechanics. please help to provide solution for the this problem.
Urgent. a = 10 , b = 7 solve this question about those information.
Knowing that a 0.02in gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11ksi, (b) the corresponding exact length (2 decimal places in 103 inches) of the aluminum bar. 0.02 in. 14 in. Bronze A = 2.4 in² E = 15 × 106 psi a = 12 x 10-6/°F 18 in. Aluminum A = 2.8 in² E = 10.6 × 106 psi a = 12.9 x 10-6/°F
The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment (1) is a tube with an outside diameter of D₁ = 3.80 in., a wall thickness of t₁ = 0.25 in., and a shear modulus of G₁ = 4,000 ksi. Steel segment (2) is a tube with an outside diameter of D₂ = 1.60 in., a wall thickness of t₂ = 0.125 in., and a shear modulus of G₂ = 12,000 ksi. The compound shaft is subjected to torques applied at B and C as shown. Determine the rotation angle of C with respect to the support at A. (1) 9 ft -0.0793 rad O -0.1090 rad O -0.1496 rad O -0.1174 rad O-0.0909 rad 1,700 lb-ft B (2) 6 ft 650 lb-ft C X