ruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional sions of the beam are b1 = 32 mm, d1 = 117 mm, b2 = 19 mm, d2 = 19 mm, and a = 6.5 mm. For this material, the allowable tensile ng stress is 13 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be d as shown to the beam. b2

ruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional sions of the beam are b1 = 32 mm, d1 = 117 mm, b2 = 19 mm, d2 = 19 mm, and a = 6.5 mm. For this material, the allowable tensile ng stress is 13 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be d as shown to the beam. b2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: At an axial load of 25 kN, a 45-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.9 mm while…

A: Axial load (P) = 25 KN = 25 × 103 N Elongation in bar (∆L) = 2.9 mm Change in width (∆b) = 0.19 mm…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L-760 mm. The…

A: Give Data: Length of beam=760 mm b1=102 mm b2=20mm d2=20mm a=6.5 mm tensile stress=10 Mpa…

Q: An aluminum alloy [E = 67 GPa; v=0.33; a = 23.0 × 10-6/°C] plate is subjected to a tensile load P.…

Q: Find the value of strain if stress is 40 N/mm2 and Youngs modulus is 70 N/mm2

A: Given data : The value of stress σ=40 N/mm2 The value of Youngs modulus E=70 N/mm2 Required :…

Q: extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 540 mm.…

Q: A copper strip (Ec= 105 GPa) and an aluminum strip (E₂ = 75 GPa) are bonded together to form the…

A: Given Data:Ecopper=105GpaEaluminum=75GpaMoment M=32 N-m It is required to calculate maximum stress…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm.…

A: FIND NA :y=36×95(952)-22×22(95-7-222)36×95-22×22y=22.637mmFIND MOI…

Q: The strain gauge measurement of a steel plate indicate the principle strains are 0.003 and 0.001.…

A: Principle strains- ε1=0.003ε2=0.001E=200 GPaμ=0.33

Q: The state of stress at a point is given by: o= 80 MPa, oy=100 MPa and tauxv =60 MPa. If the yield…

A: State of stresses-σx=80 MPaσy=100 MPaτxy=60 MPayield strength-fy=150 MPa

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 880 mm.…

Q: An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a…

Q: A constantan alloy strain gauge is mounted on a gold (Young's modulus = 90GPA) cantilever that is…

A: Given data Modulus of elasticity of alloy (E) = 90 GPa Dimensions of strain gauge Thickness (t) =…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional
dimensions of the beam are b1 = 32 mm, d1 = 117 mm, b2 = 19 mm, d2 = 19 mm, and a = 6.5 mm. For this material, the allowable tensile
bending stress is 13 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be
applied as shown to the beam.
b2
a
M
| A
В

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw a cantilever beam that is 12 feet long with the appropriate boundary conditions. Place a distributed load of 3 kips/foot on the beam and draw it appropriately. Determine the shear and moment diagrams for this beam and draw and label them correctly.
If the material is machine steel having a yield stress of sY = 500 MPa, determine the factor of safety with respect to yielding if the maximum shear stress theory is considered.
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 580 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 112 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 15 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a a M d2 A B bị
Narrow bars of aluminum are bonded to the two sides of a thick steel plate as shown. Initially, at T₁ = 70°F, all stresses are zero. Knowing that the temperature will be slowly raised to T₂ and then reduced to T₁, determine (a) the highest temperature T₂ that does not result in residual stresses, (b) the temperature T₂ that will result in a residual stress in the aluminum equal to 58 ksi. Assume aa = 12.8 x 10-6/°F for the aluminum and a = 6.5 × 10-6/°F for the steel. Further assume that the aluminum is elastoplastic with E = 10.9 × 106 psi and ay = 58 ksi. (Hint: Neglect the small stresses in the plate.) Fig. P2.121
2.27. The stress components at a given point in an engineering component are es- timated to be oxy=4.1 ksi, ơyy=0 ksi, ơz =0.9 ksi, ory =-3.1ksi, ơyz = 1.2 ksi, Ozx =0 ksi. Estimate the factor of safety against yielding using von Mises' theory if the uniaxial yield stress of the material is Sy =17.2 ksi.