The beam shown has an second moment of area of 9,500,000 mm4 and a controlling section modulus of 80,500 mm3. If a maximum bending moment of +1515 Nm is applied to the beam, determine the maximum flexural stress produced in the beam cross section. Note: Give your answer in MPa Note: Do NOT include the units in your answer 49 Answer:

The beam shown has an second moment of area of 9,500,000 mm4 and a controlling section modulus of 80,500 mm3. If a maximum bending moment of +1515 Nm is applied to the beam, determine the maximum flexural stress produced in the beam cross section. Note: Give your answer in MPa Note: Do NOT include the units in your answer 49 Answer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(a) The Figure la show the cross-section of a beam. All dimension are in cm. 10 2 10 Figure la (i) Calculate the centroid of the cross-section measured from the bottom of the cross section. (ii) Calculate the moment of inertia, I, for this cross-section. (iii)A pure bending moment of magnitude 1.0 kN.m is applied to the cross- section, generating compression above the neutral axis, and tension below. Calculate the maximum values of the tensile and compressive stress. (iv)The bending moment is removed. The same beam cross-section is now subject to a vertical shear force of 2.5 kN acting in the downward. Calculate the maximum horizontal shear stress. Where does it occur?
If the sections shown below is subjected to a negative bending moment of 10kN, draw the 3D bending stress distribution. Please show all relevant calculations and values on your distribution. The position of the neutral axis is measured from reference point A.
Parvinbhai
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3 cm and internal diameter 2.3 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis (i) The moment of inertia in (mm^4)= ii) The radius of curvature in (mm) = (iii) The maximum bending stress in (N/mm^2)= iv) The bending stress at the point 0.6 cm from the neutral axis in (N/mm^2)=
A beam has a bending moment of 3 kN-m applied to a section with a hollow circular cross-section of external diameter 3.4 cm and internal diameter 2.4 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis Solution: (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is in (N/mm^2) Answer and unit for part 3 iv) The bending stress at the point 0.6 cm from the neutral axis is in(N/mm^2) Answer and unit for part 4
A beam is subjected to a negative bending moment of 8 kN-m. The cross-sectional dimensions of the beam are shown in Figure. Determine the bending stress at point H. Include a negative sign if compression. (in MPa.) Determine the moment of inertia about the centroidal x – axis (in mm4). Determine the maximum bending stress produced in the cross section. Include a negative sign if compression (in MPa). Determine the centroid location of the cross-section from the bottom fiber of the section (in mm). v
A simply supported beam of hollow rectangular cross section is 100mm deep and 60mm wide with a wall thickness of 10mm. The beam has a span of 6m and carries a load as shown . Neglecting the weight of the beam draw a bending moment diagram and calculate the maximum bending moment. And determine the maximum bending stress in the material.
A beam has a bending moment of 4.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3.1 cm and internal diameter 2.1 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis Solution: - The bending stress at the point 0.6 cm from the neutral axis is
5. A 4-point bending test is performed on a beam of length L = 1 m. A load of P = 2000 N is applied across two loading points a distance a = 0.4 m from the sides of the beam. If the beam has a radius of r = 1 cm and a yield strength of σ = 250 MPa, does the bar yield? If it's an elastic-perfectly plastic material, does it fail all the way through the thickness of the bar? What would the yield strength of the material need to be if we wanted a factor of safety of 1.5?
The beam in (Figure 1) is made from three boards nailed together as shown. Figure d 20 mm 25 mm ✓ 200 mm M 150 mm 2 20 mm 1 of 1 Part A If the moment acting on the cross section is M = 460 Nm, determine the resultant force the bending stress produces on the top board. Express your answer to three significant figures and include appropriate units. F = Value Submit μA Provide Feedback 3 Request Answer Units ?
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3.6 cm and internal diameter 2.4 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.5 cm from the neutral axis (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.5 cm from the neutral axis is
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.65 in from the top of the beam on section 1.1 feet to the right of B if P = 1120 lb, Q = 4268 lb, w = 1.14 in, L = 8.02 in, b = 3.98 in, and h = 1.27 in. Round off the final answer to two decimal places. P Q W D E L 2 ft |、▬▬3 ft ▬▬▬3 ft▬| 2 ft F | b h