2000 Ib 300 lb/ft 6 in, TI A 4 in. -3 ft- 3 ft-

Q: for the Plane frameshown in Figure determine the axial force in cord (DE) and the horizontal and…

A: To find: Tension in cable DE. Reaction forces at A.

Q: Define hydrostatic stress state.

A: Solution: It is defined as the state in which stresses of the same magnitude and direction are…

Q: The crate has a weight of 100 Ib and a center of gravity at G rests on the floor for which the…

A:

Q: What is the V and M diagram? Thank you!

A:

Q: If a heavy cargo is lifted using a ship's crane and the load remains suspended within the ship, what…

A: When the heavy cargo is lifted using a ship's crane and the load is still suspended within the ship,…

Q: Choose correct answer: On a piston of 100 mm dia., pressure applied is  954.83 mm of Hg, then the…

A:

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: Q2 A beam is supported at A and B as shown in Figure Q2. By neglecting the mass of the beam, (a)…

A: (a) To find: The support reactions. FBD: The free-body diagram is shown below.

Q: Find roller support reaction

A:

Q: TA 500 Ib buoy, with a 2 ft radius is tied to the bed of a lake using a steel cable. What is the…

A: Mass of the buoy = 500 lb Need to determine the tensile force in the cable.

Q: In dead weight tester, the applied load is 0.017 kN, theoretical pressure is 150 kPa. Then the area…

A: Given data:  Magnitude of applied load, F = 0.017 kN. Theoretical pressure, P = 150 kPa. The…

Q: • The length where the shear is zero (x) (f applicable) • The maximum shear load (Vman) – positive…

A:

Q: If Tb is 1000 lbs, what is W?

A:

Q: 2 ft 2.5 ft 1.5 t

A: Centroid, also called the center area of anybody is the point at which the whole area of the body…

Q: 1. Solve for the total reaction at support A. O 20 kN O None of the above 80 kN 40 kN a. Determine…

A:

Q: a,b,c please and thank you!

A: The objective of the question is to determine the maximum and minimum principal stresses and the…

Q: 3) For the beam shown in Figure 1; (a) Determine the reactions at the supports. (b) Draw and label…

A:

Q: Member A 10' Member B -15' - -12' 6" - 40' Member C 1.5 KIPS

A: Consider below figure: Here, Fa = Reaction at a Ff = Reaction at f tan θ  = deef∴ θ = tan-11012.5∴…

Q: Bar one has a Young's modulus that is bigger than that of bar two. This indicates bar one:

A:

Q: Explain about the Oblique point loads at the surface ?

A: given: Explain about the Oblique point loads at the surface ?

Q: True/false Q-5 Specific weight is an extensive property? If yes why ?

A: Specific weight is define as tge ratio of weight of the substance to its volume.  w• = W/v  W = mg {…

Q: A spherical shell of 1.8 m outside diameter and 1.725 m inside diameter contains helium at a…

A: Outside diameter, D= 1.8 m Inside diameter, d= 1.725 m Pressure, P= 10.4 MPa

Q: a. 24 kN 3 m 7 kN/m B 90 kN-m 6 m V max M max 3m D 3 m 12 kN X E

A: First calculate the reactions the. Draw the sfd and bmd

Q: Given data : Area=3 cm2 Stress-40 N/cm2 Find force

A: Given data : Area=A Stress=σ   To find : Force

Q: Estimate the heat loss from human body of 36 C temperature by convection and radiation. Consider the…

A: The heat loss from human body of 36oC temperature by convection and radiation is 304.875 W.

Q: Don't use chatgpt. Need in hurry (Add FBD)

A:

Q: BM at B is 3 kN 1 m D 1m 1 m B 1 m A

A:

Q: Q) calculate the magnitude of The force P ? Wz 6 KN A M=02 Im トーon 16 KN

A: This question is related to the static equilibrium equations.  As we know the condition equation, we…

Q: Write a a brief note on eccentric impact.

A: Eccentric impact takes place when the line of the mass of the center of two bodies not coincide with…

Q: Determine the diameter, in inches, of a circular steel rod that could withstand a tensile force of…

A:

Q: In dead weight tester, the applied load is 0.017 kN, theoretical pressure is 150 kPa. Then the area…

A:

Q: To decrease the amount of force needed increase the of the inclined plane. distance or length O…

A: Given Data⇒ Inclined plane

Q: 0.75 in. 1'in. -20° 1.5 in.1 in. 3 in. 5 lb D 5 lb

A: Given,

Q: A motor car tyre contained a fixed mass

A: Given Tyre To find Importance of mass in motor car tyre   Moto car tyre is to maintain the road…

Q: A mechanic is supporting a car with a hydraulic lift. The smaller piston has radius of 3 inches and…

A: Given data:- The smaller piston has radius =3 inches the larger piston has a radius = 8 inches.…

Q: 1. Structure analysis of the window opening mechanism of my office in the pic: a.Number of moving…

A:

Q: The steel rod shown below is 2inches in diameter and is subjected to an eccentric 2000 lb load…

A: Given Data: The eccentric load is P = 2000 lb. The eccentricity is e = 1". The diameter of the…

Q: A 3000 pound force is applied to a piston causes a pressure of 800 psi. What is the diameter of the…

A: Given - Force(F)=3000 pound force = 13344.66 NewtonPressure(P) = 800 psi = 5515810 kPa Let d be the…

Q: The shaft is supported by a journal bearing at A and a thrust bearing at B. Determine the normal…

A: Given data  F1 = 2.5 kip  F2 = 3 kip W = 75 lb/ft b = 12 ft a = 6 ft c = 2 ft To determine…

Q: lestion IJ alculate the maximum stress in 0.10-i 2.00-in dia. Applied torque %3D

A:

Q: Just for checking determine if true or false 1.) Tensile force tends to cut the body in two. 2.)…

A: given; 1.) Tensile force tends to cut the body in two. 2.) FBD is a sketch of the isolated body…

Q: Consider the bar/roller assembly shown in the figure below. The roller and surface at point A are…

A: A free body diagram is defined as a diagrammatic representation of all the forces acting in a…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.