The strut on the utility pole supports the cable having a weight of P = 300 lb. (Figure 1) Figure 1.5 ft 4 ft 1 of 1 2 in. HT COI4 in. Part A Determine the absolute maximum bending stress in the strut if A, B, and C are assumed to be pinned. Express your answer in kilopounds per square inch to three significant figures. VO ΑΣΦ omax = Submit Provide Feedback Request Answer vec ? ksi

Q: Problem 1.5 The beam supports a distributed load with a maximum value of 55 lb/ft at A. Part A -3…

A: The beam supports a distributed load with a maximum value of 55 lb/ft at A.Determine the resultant…

Q: Represent the loads in the following loaded beam by half-rang Fourier sine series. P w/unit length…

A: Certainly! Let's go through each step in detail, explaining the inner workings of the process to…

Q: Part A The beam in (Figure 1) is made from three boards nailed together as shown. If the moment…

A: Now, here given Moment M = 580 N.m The given dimensions of beam are in figure , by using them we can…

Q: The shaft as shown in the figure is supported by bearings at A and B. The bearings exert only…

A: Force, F= 49.4 kN   Note: Let the left end be represented as point "C". Let the reactions at the…

Q: I need handwritten solution with explanation and diagram.

A:

Q: Determine the reaction forces at pins A, B and Cusing method of parts (frames). Show all work…

A: Consider the free body diagram shown below for the BC.

Q: If the roller at B can withstand a max load of 3 kN, determine the largest magnitude, F, of the…

A: Given: max load at roller B = 3kN now we can evaluate force F by using simple equilibrium…

Q: The beam is subjected to an internal moment of M=122 kN-m- (Figure 1) Figure 30 mm, M C 150 mm 150…

A: Part (A): Draw the diagram of cross-section of inverted T section.

Q: Figure 30 mm 250 mm 30 mm 200 mm W -25 mm V B 1 of 1 Part A If the wide-flange beam is subjected to…

A:

Q: The beam is subjected to an internal moment of M = 60 ip-ft. Figure 1) Figure (101 ▾ Part A…

A: According to the given data M=60kip.ft We need to find  Maximum Compressive and tensile stress

Q: For the wood beam shown in Figure A, assume L = 1.5 mand P = 15 kN. The beam cross section shown in…

A:

Q: (c) Determine the 1st moment of area Q, of the top-half region A' (red shaded area) against z axis,…

A:

Q: The beam in (Figure 1) is made from three boards nailed together as shown. Figure 20 mm 200 mm M 25…

A: Given: M = 640 N.m   To find: σmax

Q: Learning Goal: Use the general equations of motion for plane motion to determine the initial…

A:

Q: 2. For the force diagram shown in the accompanying illustration, draw the shear force and moment…

A: To make shear force diagram and bending moment diagram, find support reactionEquilibrium equation…

Q: Required Information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: L= 1.2 kN To find - The forces in members.

Q: The length of the cable segment AB is 10 ft (Eigure 1) The angle a = 30° Figure 10 ft ▲ Part A What…

A: The length of AB is .The angle is The weight of crate is

Q: 1 200mm 1 2₁.965 140mm RI 200 mm 1100mm 80mm son/m ←300mm + ↑ ک۹۰ 4. ✓ гном T Rz 7

A:

Q: There is no F1 or F2 force, only P against the front end of the beam. Thank you so much for any help…

A: Given data-P=5KN=5000Nσy=240 mPa=240 ×106 N/m2

Q: k P 0 8 ft x = 11.1 ft x RA 8. W (ft) Calculate the magnitude of the bending moment at distance x as…

A:

Q: truss

A: the truss using both the force method and the stiffness method. Here's a breakdown of the steps…

Q: The allowable bending stress for the bar is oallow = 200 MPa 80 mm 20 mm 10 mm 10 mm M M 10 mm Part…

A:

Q: A a= -0.5 m Submit 15 kN 195| ΑΣΦ | | Determine the minimum dimension a to the nearest mm of the…

A:

Q: Live load on the deck = 70 psf Deck weight = 6 psf Beam weight = 8 lb/ft Column weight = 80 lb…

A:

Q: The beam is subjected to an internal moment of M = 122 kN. m. (Figure 1) Figure 30 mm, C. 150 mm M…

A: Given data  Internal moment = 122kN.m  Find the bending stress at point A and B

Q: The beam is made from four plates and subjected to a shear force of V = 26 kN. (Figure 1) Figure 50…

A: According to the given dataV=26kN3We need to findShear stress point-A

Q: Please draw shear force diagram v(X) and bending moment diagram m(X)

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.