A composite beam, made of aluminum (Al) and magnesium (Mg), has the cross section shown below. The moduli of elasticity for aluminum and magnesium are EAI = 70 GPa and EMg = 45 GPa, respectively. If the allowable flexural stresses (in tension and com- pression) are oal = 135 MPa for the aluminum and M Mg = 120 MPa for the magnesium, determine the maximum allowable bending moment for the beam. 0.2 m 0.2 m 0.2 m Al Mg

Q: A simply supported beam of length 30-in diamater 2-in is supported at A and D, subject to load P at…

A:

Q: 2 KN m A simply supported I-beam has the following loadings, calculate the magnitude and location(s)…

A:

Q: Pravinbhai

A: The objective of the question is to determine the principal stresses and the maximum shear stress…

Q: A steel cantilever beam of length L = 1m has a hollow rectangular cross section. The outside width…

A: Given: The length of the beam, L = 1m The width of the beam, b = 100 mm = 0.1 m The height of the…

Q: For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the…

A: Use simply support beam concept to solve this problem, Given information Total length of…

Q: A 6 ft long 2” x 12” beam is subjected to a uniform (edge-to-edge) distributed load of 1500 lbs per…

A:

Q: Consider the beam shown in the figure. The allowable tensile and compressive of a beam material are…

A:

Q: 1. Find the resultant force in a brass beam from a normal stress of 98 MN/m2 with a square…

A: Answer 1: σ=98 MN/m2s=12 mm Need to determine the resultant force in a brass beam.

Q: .beam, simply supported at its ends, carries a load which increases uniformly from 15kN/m at the…

A: The product of the moment of inertia and youngs modulus,

Q: The beam shown below is carrying a vertical shear force v. TH Calculate the maximum shear stress (T)…

A:

Q: The diver has a mass of 75 kg and is standing motionless at the end of a diving board shown in…

A: Given data, Mass of the driver, m = 75 kg So, weight of the driver is W=mgW=75×9.81W=735.75 N Young…

Q: An S178 x 30 American standard I-beam (see Appendix A) is loaded and supported as shown below. (a)…

A:

Q: The steel beam has the cross section shown. The beam length is L = 17 ft, and the cross-sectional…

A:

Q: The beam shown below is subjected to a point load of 10kN and a uniformly distributed load of 3kN/m,…

A:

Q: Beam ABD supports an 80 kg vertical mass connected at point D. The beam has a pin connection at the…

A:

Q: A rectangular beam with two notches (with radius r = 2.5 mm) is shown in Figure 1.1. The beam has…

A:

Q: If The section below is subjected to bending moment of 30kN.m (causing compression on the top fiber)…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: A simply supported wood beam of length L = 11 ft carries a concentrated load P at midspan, as shown.…

A: The maximum shear strength is .The dimension of beam is .

Q: Determine the maximum deflection of a simply supported beam carrying a hydraulic cylinder in a…

A: Force (F) = 45 kN = 45000 NBeam length (L) = 1.5 mBeam height (h) = 150 mm = 0.15 mBeam thickness…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.