The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) Figure <1 of 1 > Part A If the allowable shear stress is allow-80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.060 rad, determine the maximum allowable forque T Express your answer to three significant figures and include the appropriate units. μÃ 4 T-5.089 kN m Submit Previous Answers Request Answer Provide Feedback ? X Incorrect; Try Again; 4 attempts remaining

The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) Figure <1 of 1 > Part A If the allowable shear stress is allow-80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.060 rad, determine the maximum allowable forque T Express your answer to three significant figures and include the appropriate units. μÃ 4 T-5.089 kN m Submit Previous Answers Request Answer Provide Feedback ? X Incorrect; Try Again; 4 attempts remaining

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-63.M. The key in Figure 1-18 has the dimensions b = 10 min, h = 8 nim, and L = 22 min. Determine the shear stress in the key when 95 N-m of torque is transferred from the 35-mm-diameter shaft to the hub. Hub End view Shear plane Shear pl T=Torque -D=Shaft diameter T=F(D/2) F₁-Force of shaf F₂= Force of hub on 1 Shear area=A,=bxL
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) Figure 1 m 1m- 30 mm 40 mm 1m P 1 of 1 > Part A If P = 22 kN, determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. Trung = 9.87 μÀ MPa Submit Previous Answers Request Answer Provide Feedback ? X Incorrect; Try Again; 5 attempts remaining
The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. A torque of 7.5 kN⋅m is applied to end A. A) Determine the maximum shear stress in magnesium. Express your answer to three significant figures and include the appropriate units. B) Determine the maximum shear stress in steel. Express your answer to three significant figures and include the appropriate units. C) Determine the shear stress on the inside surface of the magnesium tube. Express your answer to three significant figures and include the appropriate units.
answers stated in box are incorrect
Mechanics of materials I
The steel shaft is made from two segments: AC has a diameter of 0.5 in, and CB has a diameter of 1 in The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft G₁ = 10.8 (10¹) ksi (Figure 1) Figure 0.5 in. 8 in. D 500 lb-ft 12 in. 1 of 1 1 in. B Determine the maximum shear stress in the shaft. Express your answer in kilopounds per square inch to three significant figures. Tmax Submit Provide Feedback IVE ΑΣΦ. 11 | vec Request Answer ? ksi
Rev Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = Value Units Figure 1 of 1 Submit Request Answer Provide Feedback 1 m 1 m 1 m 30 mm 40 mm
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. Y le X 5 in-k bearing 25 in d bearing 30 in b 35 in bearing bearing TT C 2 2 in-k gear c: gear b: shaft ab: shaft ce: all shafts: radius 2.0 in radius 5.0 in radius 0.5 in radius= 0.7 in - G = 12000 ksi
A compound shaft consists of an aluminum tube (1) securely jointed to a steel tube (2). Both aluminum and steel tubes have an outside diameter of D= 48 mm and a wall thickness of t= 3 mm. The shaft is secured by a fixed support at one end and is subjected to a torque of T= 115 N.m at the other end. Determine the maximum stress in the shaft.[L1 = 200 mm, L2 = 350 mm, D = 48 mm , t = 3 mm, G = 75 GPa]
An aluminum shaft of two segments is shown below. Determine the allowable torque if the shear stress is not to exceed 30MPa and the angle of twist between the ends of the bar is not exceed 2.3°? (Assume G=80GPa)
at B. The allowable shear stress in the steel is 40 MPa. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the with diameterd = 38 mm transmits 37 kw malit X7-3A motor driving a solid circular steel shat shaft does not exceed the allowable limit. Motor d = 38 mm
only Handwritten answer needed please. not typed