If it is subjected to the triangular distributed load, determine the angle of twist of end A with respect to C. Take G = 75 GPa. Express your answer to three significant figures and include the appropriate units. ?

If it is subjected to the triangular distributed load, determine the angle of twist of end A with respect to C. Take G = 75 GPa. Express your answer to three significant figures and include the appropriate units. ?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Related questions

Q: Use FEM to calculate the temperature at nodes 2 and 3, as well as the heat at nodes 1 and 4. area

A: GivenT1=0oCT4=20oCKA=55×10-3 W/mmoCKB=0.1×10-3 W/mmoC

Q: A 1.5m long cylindrical barrel made of a material whose specific gravity is 3.8, shown in the…

A: GivenL=1.5msgb=3.8sggly=1.26sgwat=1

Q: A flow meter is attached to a hydraulic line that measures 8 gal/min. The line has an inside…

A: According to the given data. D=1.5in Q=8gal/min We need to find Flow rate measured in in/s

Q: A pitot-static tube is used to measure the velocity of an air stream. Air speed is expected to vary…

A: To calculate the required signal conditioning gain, we need to first determine the range of…

Q: An air standard Ericsson Cycle operates under steady- flow conditions. Air is at 120kPa and 27°C at…

A: Given data: - P1 = 120 kPa T1 = 27o C Heat rejected (QR)…

Q: A = 90 lbs h C= 110 lbs 2₁ 2 B = 70 lbs D=120 lbs Q 2²

Q: On a weather station, an altimeter was calibrated to 35 in Hg while the documented density at sea…

A: “Since you have posted multiple questions with multiple sub parts,we will provide the solution only…

Q: Develop a mathematical expression for the effective mass transfer rate achieved by an implanted drug…

A: To find: The mathematical expression for the effective mass transfer rate.

Q: What is the value that is shown by pressure gage in the following chamber? Assuming that density of…

A: To Find : The value of gauge pressure of each chamber. Given : The specific gravity of oil is…

Q: Select comfortable summer design conditions (dry bulb and relative humidity) for a machine shop…

A: To determine comfortable summer design conditions for a machine shop where people in light clothing…

Q: An experimental rocket plane lands on skids on a dry lake bed. If it is traveling at 80.0 m/s when…

A: This question will be solved using the concept of kinematics from mechanics.

Q: 1) F1 kN 0.4 m 1.2 m F2 KN 1.2m F3 KN 0.5m The beam is made from mild steel (elastic modulus 200Gpa)…

Q: Your die setter brings you a print of a cylinder with a 2 inch outside diameter and a 1.75 inch…

A: Given data: Outside diameter of cylinder, d2 = 2 inches Inside diameter of cylinder, d1 = 1.75…

Q: The system is made of 2 separate rods (cross-section is a circular). The blue rod is made from…

Q: A car starts from a stand still with a constant acceleration of 3.94 ft/ s2 for 20 seconds. At that…

A: The initial velocity of the car is 0 ft/s. The initial acceleration is 3.94 ft/s2 for 20 s. The car…

Q: The wire AE is stretched between the corners A and E of a bent plate. Knowing that the tension in…

A: Solution: Given Data: Coordinates A (-90, 160, 0) E (120, 0, 120)

Q: At what atmospheric pressure, p, will water boil at 45 °C? Express your answer in both SI and BG…

A: Introduction Atmospheric pressure is the force per unit area exerted by the weight of the Earth's…

Q: The company has opted to purchase a new viscometer for you, as such, you are required by to propose…

A: Solution: Given Data: Temperature (°C) = 40, 65, 80, 100 Time (s) = 57, 41, 29, 16 Calibration…

Q: The diagram models a juggler balancing a pole on her nose. The pole has length L and is modeled as a…

A: Given: To find: Equation of motion

Q: nt(a) Verify that Eijm³klm = Å¡k§jl¬Å¡1³jk By contracting the result of part (a) show that…

A: This question is from tensor notation. First we have to know the property of kronecher delta and…

Q: Make the indicated conversion between customary and metric units of weight and mass. 17…

Q: Hydraulic pump calculations Pressure = 600 PSI Displacement (D) = 0.4in3/rev 1150 RPM Total…

A: The given data in the question is: Pressure = 600 PSI Displacement (D) = 0.4 in3/rev Speed = 1150…

Q: Figure E8.4 shows a material chart with the two indices of Exercise E8.2 as axes. Identify and plot…

A: To show: Plot of coupling lines for selecting materials for a column with F=106 N and H=3 m, and…

Q: A Silicon Carbide powder has an internal energy of 3 X 108 J/m³, a surface tension of 1.2 J/m², and…

A: Given data: γ = surface tension = 1.2 J/m2 E = internal energy per unit volume = 3×108 J/m3 Total…

Q: A regulation basketball is initially flat and is then inflated to a pressure of approximately 23…

A: According to the given data D=4.67in P=23lb/in2 T=50°F=496 We need to find Mass of the air

Q: Consider the frame shown in (Figure 1). Suppose that F-310 lb. Follow the sign convention. Figure 3f…

Q: For flowing water at 10°C, what is the magnitude of the velocity gradient needed to produce a shear…

Q: At what atmospheric pressure, p, will water boil at 25 °C? Express your answer in both SI and BG…

A: To find: The atmospheric pressure. Given: The temperature is T=25°C. Concept used: Atmospheric…

Q: EXERCISE 3.16 Collar A is welded to the vertical shaft, so is constant. The rectangular plate is…

A: Given: To find: Rotation transformation

Q: M Question3: Determine the moment of inertia about the Y-Y axis for the shape below. Consider a164…

A: According to the given data There are two shape 1=Rectangle 2=half circle We need to find the moment…

Q: For the gate below, which is fully submerged find the centroid, center of pressure from the surface…

A: This question is based on the concept of fluid mechanics.

Q: ᴀ 39.37-ᴄᴍ x 55.85-ᴄᴍ, 327-ʀᴘᴍ, 16-ᴄʏʟɪɴᴅᴇʀ, 4-ꜱᴛʀᴏᴋᴇ, ꜱɪɴɢʟᴇ-ᴀᴄᴛɪɴɢ ꜱᴛᴀᴛɪᴏɴᴀʀʏ ᴅɪᴇꜱᴇʟ ᴇɴɢɪɴᴇ ɪꜱ…

A: The number of cylinders is n=16 The diameter of the cylinder is d=39.37 cm=0.3937 m The stroke…

Q: The water sprinkler, positioned at the base of the hill, releases a stream of water with a velocity…

Q: The tensile modulus of a 0°, 90°, and 45° graphite/epoxy ply is measured as follows to give E1 =…

A: Solution: Given Data: E1=26.25 MsiE2=1.494 MsiEx=2.427 Msi To Find: (a) Value of Ex for 30o ply.…

Q: For each of the systems shown in Figure P4.52, the input is the force f and the outputs are the…

Q: As water flows through the pipe, it rises within the piezometers at A and B to the heights of hA=…

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: To find- The magnitude of the horizontal and vertical component of the force exerted by the static…

A: Given

Q: The elevator E shown in the figure moves upward according to the velocity profile that is presented.…

A: The elevator accelerates and decelerates at a constant rate 0.17 m/s2. The height travel by elevator…

Q: Determine the following 1. Determine what substance has a great strength? Calculate and…

A: Given: To find: 1. Determine what substance has a great strength? Calculate and demonstrate. 2.…

Q: For PCB, why do you need to know the thickness,diaelectric constant and loss tangent for design?…

A: This question is based on the concept of PCB design.

Q: Use an energy method to obtain the expression for the natural frequency of the system shown.

A: To Find : The natural frequency of the system. Given : Concept : the mass m1 moves downward x…

Q: A conservative mechanical system consists of a mass m that is constrained to move along a circle of…

A: Given: To find: Degree of freedom Lagrangian Euler-Lagrange equation

Q: thif the state of stress at a point is 300 0 0-200 0 find (a) the magnitude of the shearing stress…

A: Given: The state of stress at a point is : T=300000-200000400 kPa Solution: (a) Unit vector for the…

Q: Knowing that connecting rod BD has a uniform cross section of area equal to 800 mm², determine the…

Q: State 1 for a dual combustion engine is P1 = 1 atm and T1 = 60.3°C; rk = 18; at the end of the…

A: Given data:- At state 1 P1 = 1 atm T1 = 60.3o C…

Q: The displacement of a body performing simple harmonic motion is described by the following equation…

A: dfds

Q: Replace the two forces acting on the pole by a wrench. Write the force R and moment M associated…

Q: Compute the hydrostatic pressure (psi) that a drilling mud with relative density equals 1.4 creates…

A: Given data:- relative density = 1.4 depth =12000 ft density of water 62.4lbm/ft3 To find:-the…

Q: m³/s. Two pump impellers with different diameters run at two different speeds under kinematically…

Concept explainers

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.

Question

Fundamental Problem 5.14
The 90-mm-diameter shaft is made of steel.
(Figure 1)
Figure
B
15 kN-m/m
400 mm
600 mm
< 1 of 1
Part A
If it is subjected to the triangular distributed load, determine the angle of twist of end A with respect to C. Take G = 75 GPa.
Express your answer to three significant figures and include the appropriate units.
μÅ A
-4
PA/C 5.59 107
C
rad
Submit Previous Answers Request Answer
Provide Feedback
?
X Incorrect; Try Again; One attempt remaining

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
A alm T 1.20 m T B 1.20 m C 3 T The 60 mm diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow 80 MPa. Find the corresponding angle of twist of disk A relative to disk C. Note: You will need to calculate the maximum allowable torque T first. Provide your answer for angle of twist in radians with 3 significant figures after the decimal point.
3. From the figure shown below, determine the stress of member AB and BC. And calculate the maximum angle of twist of the shaft. 15 kN-m 10 kN-m G = 82.5 GPa A IB diameter = 60 mm diameter = 50mm %3! 1.2 m 0.8 m
PROBLEM: A shaft supported at the ends carries a spur gear and is to transmit 10 kW at 200 rpm. The weight of the gear is 1 kN. If the allowable shear stress is 45 MPa, determine the shaft diameter. FIGURE: Bearing 150 mm 100 mm. 200 mm. Gear Shaft 100 mm Bearing SOLUTION: Instructions: Solve the diameter of the shaft. To add an equation in Word, select Insert > Equation or press Alt + = Example: = F A
Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m %3D 2 m 100 mm 50 mm T= 50 kN. m
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad