Problem 4-1. For the following shaft determine the support reactions, and maximum shear stress in AB and BC. Given: T = 1.2 kN.m; G = 26 GPa; Ger = 39 GPa 300 mm 450 mm Br A - 38 mm B 50 mm

Q: LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices…

A: Identify the feature displayed in the picture, and choose from choices below.

Q: Q/Draw S and B-M D 8 kuim

A:

Q: Which of the following are performed to check an NC part program before it is run? Select one or…

A: CNC machines utilize a set of codes to perform the cutting operations on the part. Codes may consist…

Q: 60 10 20 45 35 15 30 2Holes DIA 20 20 60 10 120 30 15

A: Given :-  Orthographic view Draw :- Front view  Top view and Right side view

Q: Which of the following is considered to be an "accelerator" in an automobile? * All of them. gas…

A:

Q: Example 39: Replace the three forces shown in Fig. below, acting on the plate by a wrench. Specify…

A: When multiple forces act on an object, the resultant force is the force that creates the same…

Q: But there is no 2 & 4 option to the multiple choice

A: Explanation: The interior of the semi circular log is made hollow so definitely center of gravity…

Q: You can change any of the layer properties, including - * aut cad color only O - None of the above.…

A:

Q: What type of scale is 1:20? O Full Scale O Enlargement Scale O Reduction Scale O O O

A:

Q: What type of scale is 10:1? O Full Scale O Enlargement Scale O Reduction Scale

A:

Q: uestion 1 (: Listen Modify panel zuestion 2 Listen Paper space tab(s)

A: The Modify tools can be accessible through the keyboard, the pull-down menu, or the toolbar, as…

Q: A composite beam is fabricated by bolting two 2.3-in.-wide by 14-in.-deep timber planks to the sides…

A:

Q: Q. 8.) ZV=0 RA+RI = L0+20 +20+20 20+20 +20+20十 ZMA=0 20x3 +2OX6+20x9+20x12. +20 X 1S +20x18+20x21…

A:

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: I Need Help With This SolidWorks Assignment With A Step By Step Process... Quick solution pls 56 88…

A: Open solidworks software and then select new part and set unit system to MMGS. Create a sectional…

Q: A graphical language used by engineers, draughtsman and other technical personnel Technical Writing…

A: Solution:

Q: Name the feature shown below. 10 00

A: the feature displayed in the picture is extrude

Q: OFFSET command use to draw object parallel to selected object by determine radius distance point…

A: Computer-aided drawing is the way to draw the various views of the component. In the orthogonal…

Q: 4) FIND EGNS FOR VEM DRAW VEM DIAGRAMS 0 200 kit 30

A:

Q: Stoker

A:

Q: In milling machine axis controls the spindle movement in the upward direction. a. Negative Y b.…

A: Milling Machine: Milling is a multi point cutting tool machining operation used for removing a layer…

Q: The part view should.com RANCES be the same CHD APPVD MIG GA as picture. 2- The color is RGB as DWG…

A: Find Draw the given object using the drawing.

Q: OA F >F>F OE- F = F, F, >F, >F, F > F, >F, D) OF> F >F,

A: Forces on the surfaces, F1,F2,F3 Area of each surfaces, 2S,S,3S

Q: I need these three parts answered (Multiple Choice). If you can not answer all three parts please…

A: Inverted section view is used on the main views of section B-B. Hence, the correct choice is (a).

Q: Freehand sketch a set of front/top/right views

A: According to the given data A 3D object is given We need to draw Three projection view of the object…

Q: DRAW THE MULTIPLE VIEW

A: The given view is in isometric view

Q: The reading of Vernier Caliper shown in the Figure is 10 30 60 70 80 1 4. 6. 7. 9. 10 .02 mm 29.54…

A: Given data: Main scale reading = 27 mm Need to determine the scale reading.

Q: The part view should be the same as picture. 2- The color is RGB as 0,220,100. 3- Should use the…

A: Find Draw the given object using the drawing.

Q: What type of scale is 1:1? Full Scale O Enlargment Scale Reduction Scale

A: Scale factor is the ratio of the length of the drawing to the actual length of the object. The scale…

Q: Draw the multiple view

A: Given isometric view

Q: Name the feature shown below.

A: The given figure is of

Q: 2. Draw the auxiliary view of the orthographic views above.

A:

Q: A00007: Drafting Competencies - To create drawing view B' it is necessary to select drawing view 'A'…

A: Break view in the solidworks is used to display the larger drwaing in smaller drawing sheet by…

Q: -30- R-64 20 -10 (5.0) -50 -40 -30 -20 -10 10 10-

A: given:

Q: How did you get the Tsat values

A: This question is based on the properties of water at different temperatures and pressure.

Q: LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices…

A: Identify the feature displayed in the picture, and choose from choices below.

Q: Given: Top, Front, & Right Views Sketch: Isometric View Front Front Front Front

A:

Q: alalale the vorFidene by an going frem AR. slake A oc for each t ABE b) ABG O ACdirectly

A: Data given - A P-V graph  Need to calculate by path  a)  ADC  b) ABC  c) AC

Q: Q1: Draw the orthographic Projections of given object. 15 20 R20 O REDMI NOTE 9 PRO MAX O AI QUAD…

A: Orthographic Projection is a 2 dimensional projection of a 3 Dimensional object.

Q: Name the feature below. (Hint: A type of selection)

A: The commands which are used in AutoCAD is noted above.

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.