A solid steel shaft AB shown in Fig. 5-13 is to be used to transmit5 hp from the motor M to which it is attached. If the shaft rotatesat o = 175 rpm and the steel has an allowable shear stress ofTallow = 14.5 ksi, determine the required diameter of the shaft to thenearest in.Fig. 5-13

Answered: Image /qna-images/answer/0e18541a-510c-4d09-96d7-3f468bc8456f.jpg

A solid steel shaft AB shown in Fig. 5-13 is to be used to transmit 5 hp from the motor M to which it is attached. If the shaft rotates at w = 175 rpm and the steel has an allowable shear stress of Tallow = 14.5 ksi, determine the required diameter of the shaft to the nearest in. Fig. 5-13

A solid steel shaft AB shown in Fig. 5-13 is to be used to transmit 5 hp from the motor M to which it is attached. If the shaft rotates at w = 175 rpm and the steel has an allowable shear stress of Tallow = 14.5 ksi, determine the required diameter of the shaft to the nearest in. Fig. 5-13

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Partial answer (a) max and min shear stress = +- 10.6 kpsi (b) vB=-0.0102 in and wB=.0234 in
i need the answer quickly
Rev Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = Value Units Figure 1 of 1 Submit Request Answer Provide Feedback 1 m 1 m 1 m 30 mm 40 mm
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which 250 mm has a 150 mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T = 340 N. m. The shaft 100 mm is machined from steel with S, = 420 MPa. Using a factor of safety of 2.5, determine the minimum allowable diameter of the 250 mm section of the shaft based on a static yield analysis using the distortion energy theory and maximum shear stress theory.
Design a hallow shaft (Diameter and length) that develops 80 kN of power while rotating at a speed of 4000 rpm. The design constrains are as under: The angle of twist not to exceed 0.200 Shear stress is not to exceed 480 MN/m? The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m?.
Design a rigid flange coupling to transmit a torque of 228N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa > Provide FBD
A motor driving a solid circular steel shaftwith diameter d = 1.5 in. transmits 50 hp to a gear atB. The allowable shear stress in the steel is 6000 psi.Calculate the required speed of rotation (number ofrevolutions per minute) so that the shear stress in theshaft does not exceed the allowable limit.
A drive shaft running at 2500 rpm has outer diameter of 80mm and innerdiameter of 60mm. The allowable shear stress in the shaft is 40MPa. Determine themaximum power that can be applied.
with diameter d = 38 mm transmits 37 kW to a gear Calculate the required speed of rotation (number of at B. The allowable shear stress in the steel is 40 MPa. X7-3 A motor driving a solid circular steel shaft revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit. Motor d = 38 mm B
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of 796 N. m.
The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) Figure 1.20 m 1.20 m 1 of 1 Part A If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.060 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. T = Submit Value Provide Feedback Request Answer Units ?
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M