SITUATION 2 A 5.25-meter simply supported beam is to be designed using stone-reinforced concrete. The beam section has width of 350 mm and depth of 600 mm. The beam is expected to be subjected to a total uniform dead load of 20.0 kN/m (including beam weight) and a uniform live load of 25.0 kN/m. Design the beam as a singly-reinforced beam by providing the final detailing of the section. The recommended material properties to be used for design are as follows: 28-day compressive strength of concrete is 30 MPa and the yield strength of the reinforcing steel is 420 MPa. Use concrete cover of 40 mm, stirrup diameter of 10 mm, and maximum aggregate size of concrete mix of 18 mm. Type your final answer/s in the text box below. Paste an image of the final designed section in the text box as well.

SITUATION 2 A 5.25-meter simply supported beam is to be designed using stone-reinforced concrete. The beam section has width of 350 mm and depth of 600 mm. The beam is expected to be subjected to a total uniform dead load of 20.0 kN/m (including beam weight) and a uniform live load of 25.0 kN/m. Design the beam as a singly-reinforced beam by providing the final detailing of the section. The recommended material properties to be used for design are as follows: 28-day compressive strength of concrete is 30 MPa and the yield strength of the reinforcing steel is 420 MPa. Use concrete cover of 40 mm, stirrup diameter of 10 mm, and maximum aggregate size of concrete mix of 18 mm. Type your final answer/s in the text box below. Paste an image of the final designed section in the text box as well.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Flexure beam.
RCC.
The reinforced concrete beam having span of 6 m carrying total design load of 30.6 kN/m as shown in figure Q3. Using following design data, design main reinforcement for the beam. Design data: The characteristic strength of reinforcement steel (fy) = 500 N/mm2 The characteristic strength of concrete is (fcu) = 30 N/mm2. Diameter of tension reinforcement is 25 mm, Diameter of compression reinforcement is 16 mm if required. Diameter of shear link 8 mm Concrete cover 40 mm,
A rectangular cantilever beam has a width of 250mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The depth of the concrete stress block is?
Based on Eurocode 2 (2004), the flexural capacity of the section shown below Is 60 kN.m for the concrete cylinder strength (fem) of 40 MPa. Estimate the flexural capacity of the section if the concrete cylinder strength (fcm) becomes 30 MPa. 150 mm Lever arm (z) = 180 mm
A prestressec concrete beam 300 mm wide and 600 mm deep is prestressed using 5 high tension bors f 12 mm o provide at 220 mm from the soffit of the beam. The effective stress in the steel is 800 N/ m Find the bending that niust be applied to the section to just auoid tension at the soffit of the beam.
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
If the given beam section is used for a simply supported beam 5.0 m span, using fc = 21 MPa and fyt = 280 MPa: 10-mm-dia 425 mm @ 200 mm 500 mm -275 mm 75 mm 25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. = kN 26. Calculate the nominal shear strength of the stirrups, Vg = kN. 27. Calculate the design sectional shear strength of the beam = kN 28. Determine the maximum factored uniform load in that can be sustained based on shear strength of the cross-section only. = kN/m 29. Determine the maximum live load in that can be sustained based on shear strength of the cross-section only. = kN/m 30. If the total factored uniform load is 60 kN/m, calculate the ultimate shear force at critical section for shear in kN. = kN INPUT ALL ANSWERS ROUNDED TO WHOLE NUMBER
i need the answer quickly
using the table below, answer the question