A beam has a flange width of 810mm and a slab thickness of 50mm. The width of the web section is 300mm and it has an effective depth of 550mm. It is reinforced at the bottom with a steel area of 1750mm2. fc’ = 20MPa, fy = 400MPa. The magnitude of the compressive force of concrete is ____kN

A beam has a flange width of 810mm and a slab thickness of 50mm. The width of the web section is 300mm and it has an effective depth of 550mm. It is reinforced at the bottom with a steel area of 1750mm2. fc’ = 20MPa, fy = 400MPa. The magnitude of the compressive force of concrete is ____kN

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Related questions

Q: A pump is tested as shown in figure for water and for one setting of the valve in the discharge line...

A: Pump is a device that moves liquids, gases and sometimes slurries from lower elevation to higher ele...

Q: A strip footing (6 m wide) is designed for a total settlement of 40 mm. The safe bearing capacity (s...

Q: A cylindrical pressure vessel is supported as shown in the figure. The internal pressure p = 1 MPa. ...

A: "Only first part of this question has been attempted. To solve the second please repost the complete...

Q: Use virtual work method. Find vertical displacement of joint B in mm due to a -2 mm fabrication erro...

A: ###Find vertical displacement of joint B in mm due to a -2 mm fabrication error on members BE and ...

Q: A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle B2 is 158...

Q: According to the truss shown in figure, The force in member CH (FCH) in KN is (T: Tension and C: Com...

Q: The recessed rectangular gate is located at an angle of 45 to the water surface. The gate is 5 m wid...

Q: The bar ABCD is supported by a pin at A, a steel wire at B, and aluminum wire at D. Deterine the str...

Q: A catchment consists of 30% area with runoff coefficient 0.40 with the remaining 70% area with runof...

Q: Determine the magnitude of the total force on one face of the area, in kN. * 2. Determine the locati...

A: Hydrostatics:

Q: There are two identical groundwater pump facilities that is operating 6 kilometers apart. The hydrau...

Q: nswer by showing which dimensionless parameters you are keeping constant. vious that you cannot chan...

Q: In a river carrying a discharge of 142 m/s, the stage at a station A was 3,6m and the water surface ...

Q: The layer is subjected to a uniform vertical stress increase of 100 kPa. The singly-drained clay lay...

A: Given:- The increase in vertical stress = 100 kPa A coefficient of consolidation for single-drained ...

Q: The pump in the figure draws water from a reservoir. At point A on the suction pipe an open manomete...

Q: As shown in the figure, if the area of the member of the truss for tension is 300 square millimeter ...

Q: The sludge produced from the aeration tank of the activated sludge process has a solid content of 2%...

Q: What will be minimum number of bolts required in each row for a suitable bolted bracket connection o...

A: Given data,

Q: Need answer ASAP. Please be detailed and clear with your solution. V. A wooden buoy of specific g...

A: We will use basic methods to solve. Weight will be balanced by bouyancy force.

Q: Since the maximum force in the h=? cable in the figure is 500 tons, calculate the maximum sag h and ...

Q: D (5000 mm) (4000 mm) E (5000 mm) 3 m (4000 mm) (5000 mm) B (5000 mm?) 100 kN 2 panels at 4 m = 8 m ...

Q: The triangular channel (n = 0.013) shown in the figure is to carry water at a flow rate of 38.5 m3/s...

A: Calculate the critical (a) depth, (b) velocity and (c) slope.

Q: 1. Shear and Moment Diagram: F2 kN F1 kN/m F3 kN/m B E 1 m 3 m 2 m 3 m Shear Equation Moment Equatio...

Q: Calculate normal stress and strain

A: Given data : Original length of bar L=100 mm Change in length of bar ∆L=0.15 mm Cross sectional area...

Q: Calculate the count of cycles resulting in breakdown. Given : Crack length = 0.2 mm 3 Fracture tough...

A: Given data- Crack length=0.2 mmFracture toughness=1708 N/mm3/2Cyclic loading=175 N/mm2Crack growth r...

Q: A granular soil has Yat = 18 kN/m3 and o' = 32°. An infinite slope is required to be made from this ...

Q: The triangular channel (n = 0.013) shown in the figure is to carry water at a flow rate of 38.5 m3/s...

Q: Three planks of wood were joined together to form the T-section shown in figure A. The beam is the s...

Q: According to the truss shown in figure, The force in member CH (FCH) in KN is (T: Tension and C: Com...

Q: For the given beam below, take P = 30 kN, W= 4 kN/m, and L= 3.5 m to solve the followings: L/2 B 3L/...

A: Answer We know that the total number of possible joint displacement which can take place due to the ...

Q: Determine the total displacement of joint D.

Q: 1. A hollow steel column is subjected to a load of 180-KN, determine the change in length if the mod...

Q: 02. Given the figure below determine the velocity (In fps) of block A as it hits tho surface 410 b- ...

A: To determine the velocity of block A as it hits the surface at B. Given, Weight of block A (WA) = ...

Q: 7. A sample of fine aggregate weighs 544 g when SSD and 530 g when OD. The flask weighs 654 g when f...

Q: An elevation must be established on a benchmark on an island that is 520.02 ft from the nearest benc...

Q: If the sensitivity of an irrigation module is 0.5, then what percent variation in outlet discharge w...

Q: The soil of an 21 degree infinite slope is subjected to full depth seepage. The soil properties are ...

Q: Draw the shear and moment diagram using area method.

Q: Given the following beam loadings 1.) Derive the shear and moment equations 200 N 1000 N/m 60 N.m 0....

A: Given, Fbd of beam:-

Q: The Figure below gives an example of a network to pump water from a lower reservoir to an upper one....

A: Quantity of water required in a building per day is calculated by number of inhabitants multiplied b...

Q: 30kN/m 12ET 3E

Q: Using the force method (mohr's integral). calculate the fixed end moment of a beam fixed at A and B ...

Q: Compute the net area of each tension member. Note that for a standard-size bolt hole, hole dia = bol...

Q: Calculate the volume of water in the dam at the end of the year assuming no outflows for downstream ...

Q: A two lane pavement ( 7 m wide) on a national highway in plain terrain has a curve of radius 350 m. ...

Q: triangular chan Tigure to carry vater at a flow rate of 38.5 m3/s. Calculate the critical (a) depth,...

Q: 90° elbow in a horizontal pipe is used ameter of the entire elbow is 10 cm. The e pressure at the ex...

Q: Figure below shows the stresses on an element ABCD. Determine the sum of normal and tangential stres...

Q: Given the following beam loadings 1.) Derive the shear and moment equations 200 N 1000 N/m !! 60 N.m...

Q: The given data of a proposed Manila-Cavite Coastal Road is tabulated below. The free haul distance i...

A: We have to compute the limit economic haul and free haul volume and overhaul volume as per the given...

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
The T-beam shown in figure resulted from monolithic construction of the beam and slab. The effective flange width is 1100 mm and the uniform slab thickness is 120mm. Width of beam is 340 mm, total depth of the T-section is 590 mm. The centroid of steel is 70 mm from extreme concrete fiber. Concrete strength f’c= 21 MPa amd steel strength fy= 415 MPa. 1 Calculate the nominal strength of the beam for positive moment neglecting the contribution of the top reinforcement, KN-m A 428.55 B 503.20 C 355.96 D 637.52 2 Calculate the nominal strength of the beam for negative moment, KN-m A 289.88 B 275.53 C 311.67 D 325.48
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
A singly reinforced rectangular section has a width of 250mm and an effective depth of 460mm. The concrete has a compressive strength of 21MPa. The steel has a yield strength of 275 MPa and E = 200,000 MPa. Calculate the ideal flexural strength for the following areas of steel: a. 2580 mm² b. 5160 mm² c. The value at balanced failure
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340 mm Thickness of flange tf = 140 mm Effective depth d = 350mm Effective concretee covering d' = 75mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = _________ mm2
A rigid steel plate is supported by three posts of high-strength concrete each having an effective cross-sectional area A = 40,000 mm2 and length L = 2 m (see figure). Before the load P is applied, the middle post is shorter than the others by an amount s = 1.0 mm. The allowable compressive stress in the concrete is 20 MPa and E of concrete is 30 GPa. What is the minimum load P (kN) needed to close the gap? P S
A rectangular beam has a width of 258mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 279MPa. The depth of the concrete stress block is ___ mm.
A rectangular beam has the dimensions (see Figure) b = 12 in, h= 20 in, and d= 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in?. The concrete compressive strength fe is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the stress in the steel caused by a bending moment M = 10 ft-kips. 9 - 6.78 in, I- 4067 in, Es = 29000000, E - 3600000 L17 in. 20 in. 3 #9 bars (A, - 3.00 in.) 3 in. -12 in.- Select one: a. 2525 psi b. 2412 psi C. 2615 psi d. 2817 psi
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
Determine the required tension steel area of the T beam with given properties below. Width of flange bf= 410 mm Width of web bw = 250mm Thickness of flange tf = 130 mm Effective depth d = 380 mm Effective concrete covering d' = 75 mm Compressive strength of concrete fc' = 34 MPa Yield stress of steel bar fy = 275 MPa Mu = 400 kN-m As mm2
Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow)con = 2.4 ksi and (allow)st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 × 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 10 ft 9 in. H 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. Pmax = Submit 04 μA Provide Feedback Value Request Answer Units ?
c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) – M1= 35kN.m and (ii) – 120kN.m Cross-section: width height Modulus of elasticity: concrete reinforcement Reinforcement: depth area b:= 300-mm h := 520-mm Ec:= 30-GPa Es:= 200-GPa d:= 460-mm As 1470-mm 2 h d b